Cannondale Trigger 27.5/29 Owner'S Manual Supplement Download Page 8

12

13

130728.PDF

Cable tension is released.

FLOW

STOP

“35% Sag”

O-RING

POSITIVE AIR

NEGATIVE AIR

EN

rear shoCk

WARNING

Use  onLY HIGH-pRessURe AIR pUMp – CAnnonDALe – 1Mp01/sLV   to set oR ReAD pRessURe.

 Use of an  incompatible pump 

(one not designed for the high pressure range of the shock) , can result serious personal injury  or result in an improper  pressure setting 
or reading which can contribute to a loss of rider control and accident. 

setting pressure

1.  Set the shock in full travel mode.

2  Release negative air pressure.

3.  Set positive pressure based on chart.

4.  Set negative pressure based on chart.

5.  Set FLOW and ELEVATE rebound adjusters based on 

chart.

6.  Check sag.  If you want more sag (softer), drop one 

weight range on the chart.  If you want more sag 
(firmer), go up one weight range on the chart. and 
repeat steps 1-5.

setting sag

1.  Slide the small O-ring up against the stop.

2  Sit on the bike in a riding position. 

3.  Dismount and inspect the O-ring position on the sag 

indicator.  The center marking between is the 35% sag 
area.  

 

35% sag - trail
40% sag - enduro

POSITIVE AIR

NEGATIVE AIR

LOW LIMIT 

100 psi

0 psi

HIGH LIMIT

450 psi

400 psi

NOTICE

Observe limits. Clean suspension pump and 
valves before attachment. 

Disconnecting the pump results in very small pressure loss. To determine actual loss for your pump, set 
pressure, disconnect and reconnect. You can compensate by adding the loss to the table values. 

RIDeR WeIGHt

tRIGGeR 27.5

tRIGGeR 29

POSITIVE AIR  

NEGATIVE AIR  

REBOUND

POSITIVE AIR  

NEGATIVE AIR  

REBOUND

Lbs

Kg

CRB

ALLOY

CRB

ALLOY

CRB

ALLOY

CRB

ALLOY

100-109

45-49

175

175

180

150

12

160

135

12

110-119

50-54

195

195

195

165

12

180

150

12

120-129

54-59

210

210

210

180

11

195

165

12

130-139

59-63

230

225

225

190

11

215

180

11

140-149

64-68

250

245

240

205

10

230

190

10

150-159

68-72

265

260

255

220

10

245

205

9

160-169

73-77

280

280

265

235

9

260

220

8

170-179

77-81

295

295

280

250

8

275

235

7

180-189

82-86

315

315

295

265

7

295

250

6

190-199

86-90

335

335

315

285

6

310

260

5

200-209

91-95

350

350

325

300

5

325

275

4

210-219

95-99

370

370

340

310

4

340

290

3

220-229

100-104

385

385

355

325

3

360

300

2

230-239

104-108

405

405

370

340

2

375

315

1

240-249

109-113

420

420

385

355

1

390

330

0

Air pressure listed in (psi). 

ReBoUnD Counter-clockwise clicks out from closed.

Summary of Contents for Trigger 27.5/29














Reviews: