background image

10 | Cannon Power Flue

REGULATORY LOCATION

MINIMUM CLEARANCES REQUIRED FOR BALANCED FLUE
TERMINALS, FAN ASSISTED FLUE TERMINALS, ROOM SEALED APPLIANCE
TERMINALS OR THE TERMINALS OF OUTDOOR APPLIANCES.

F

n

b

d

a

k

k

h

h

h

j

e

e

g

c

T

T

T

g

d

j

j

See note 2

See note 3

Openable
window

Door

I

P

M

T = Flue terminal                         M = Gas meter
I = Mechanical air inlet               P = Electricity meter or fuse box

Shading indicates prohibited
areas for flue terminals

Ref                                                                   Item

Minimum clearances

(mm)

Natural

draft

Fan

assisted

- unless appliance is certified for closer installation

Notes:
1 All distances are measured to the nearest part of the terminal.
2   Prohibited area below electricity meter or fuse box extends to ground level.
3   See clause 5.13.6.6 for restrictions on the flue terminal under covered areas.
4   See Appendix J. Figures J2(a) and J3(a), for clearances required from a flue terminal to an LP

Gas Cylinder. A flue terminal is considered to be a source of ignition.

5   For appliances not addressed above acceptance should be obtained from the technical regulator.

Special Note:

This chart MUST be read in-conjunction with
the full Australian Standard Gas Installations AS/NZS 5601.1

THE POWER FLUE HEATER IS FAN ASSISTED. SEE COLUMN HIGHLIGHTED

a               Below eaves, balconies and other projections:

Appliances up to 50 MJ/hr input                                                                       300                200
Appliances over 50 MJ/hr input                                                                        500                300

b               From the ground, above a balcony or other surface                                              300                300
c               From a return wall or external corner                                                                     500                500
d               From a gas meter (M)  (see 4.7.11 for vent location of regulator)                        1000              1000
e               From electricity meter or fuse box (P)                                                                    500                500
f                From a drain pipe or soil pipe                                                                                 150                  75
g               Horizontally from any building structure   or obstruction facing a terminal             500                500
h               From any other flue terminal, cowl, or combustion air intake                                 500                500
j                Horizontally from an openable window, door, non-mechanical air inlet or other opening into a

building with the exception of sub-floor ventilation:

Appliances up t 150 MJ/hr input                                                                       500                300
Appliances over 150 MJ/hr input up to 200 MJ/hr input                                 1500              1500
Appliances over 200 MJ/hr  input                                                                   1500              1500
All fan assisted flue appliances, in the direction of discharge                                              1500

k               From a mechanical air inlet, including a spa blower                                             1500              1500
n               Vertically below an openable window, non-mechanical air inlet, or any other opening into a building

with the exception of sub-floor ventilation:

Space heaters up to 50 MJ/hr input                                                                 150                150
Other appliances up to 50 MJ/hr                                                                      500                500

Appliances over 50 MJ/hr input and up to 150 MJ/hr input                            1000              1000
Appliances over 150 MJ/hr                                                                             1500              1500

FIG 5

Summary of Contents for Fitzroy FITZIB-PMEXx

























Reviews: