background image

27

improper maintenance, crash, misuse 

or collision. Subject to the terms and 

conditions of this warranty, leaking 

seals will be replaced within 90 days 

from the original date of purchase. 

Such replacement notwithstanding, 

seals are subject to relative movement 

between parts and are normal wear-

and-tear items not subject to warranty 

coverage. This limited warranty gives 

the consumer specific legal rights. The 

consumer may also have other legal 

rights which vary from state to state 

or country to country. Some states and 

countries do not allow the exclusion or 

limitation of incidental or consequential 

damages or warranties, so the above 

limitations or exclusions may not apply 

to you. If it is determined by a court of 

competent jurisdiction that a certain 

provision of this limited warranty does 

not apply, such determination shall not 

affect any other provision of this limited 

warranty and all other provisions shall 

remain in effect.

THIS IS THE ONLY WARRANTY MADE 

BY CANE CREEK ON ITS SUSPENSION 

PRODUCTS AND COMPONENTS, AND 

THERE ARE NO WARRANTIES THAT 

EXTEND BEYOND THE DESCRIPTION 

HEREIN. ANY WARRANTIES THAT 

MAY OTHERWISE BE IMPLIED BY 

LAW INCLUDING, BUT NOT LIMITED 

TO, ANY IMPLIED WARRANTY OF 

MERCHANTABILITY OR FITNESS FOR A 

PARTICULAR PURPOSE ARE EXCLUDED.

Warranty Information 

Summary of Contents for Helm





























Reviews: