background image

Page - 7 - 

D7292/12 

MISCELLANEOUS DATA 

 

 

 

    Combined 

 

 Sounder 

 

 

 

 Strobe 

 

Weight (kg). {dc}        

     5.0   

 

    4.4   

    

   4.1 

   

 

    {ac}        

     5.6   

 

    4.7   

    

   4.4 

 

All metal castings are of LM6 aluminium alloy, corrosion resistant, anodised and outside surfaces 
finished with a polyester paint coating. 

 

The strobe dome is of clear borosilicate glass. 

 The 

sound-shaping 

components are of flame retardant ABS. 

 

The coloured lens is of flame retardant polycarbonate. 

 

All external fasteners are of stainless steel. 

 

All sounders have 32 sound signal selections.  From the 32 sound signals, any signal may be chosen 
as the first stage alarm and any signal for the second stage alarm. 

 

Sound output level and current consumption depends upon the signal selected. Typical sound output 
level at 1 metre is 110dB(A) and typical current consumption is 350 mA for 24VDC, 110 mA for 115 
VAC and 55 mA for 230 VAC depending upon sound signal selected. These values apply for Gas 
Group IIB; for Gas Group IIB+H2, sound output is reduced by typically 3dB. 

 

All strobes have a xenon flash rate of 1Hz, one flash per second.  The flash energy is 5 joules with a 
typical current consumption of 220 mA for 24VDC, 135mA for 48VDC, 90 mA for 115 VAC and 45 mA 
for 230 VAC. 

 

 24VDC 

48VDC 

115VAC 

230VAC 

5 JOULES 

220mA 

130mA 

90mA 

45mA 

10 JOULES 

500Ma 

300mA 

105mA 

53mA 

20 JOULES 

1.1A 

500mA 

260mA 

170mA 

 
 
 
WARNING: POSSIBLE ELECTROSTATIC RISK 

The Horn and Lens may become electro-statically charged and should not be touched or rubbed when in 
operational service. If cleaning is required follow the warning given on the equipment label and clean only 
with a suitable damp cloth.  

 

 

THREADED CABLE ENTRIES 

All threaded cable entries to be fitted with an ATEX certified component and the thread sealed with a suitable 
non-setting thread sealant to maintain IP66 rating. 
 

 
SPECIAL CONDITIONS FOR SAFE USE (BASEEFA CERTIFIED) 

  The equipment incorporates flameproof joints which have a maximum gap less than that 

stated in the standard EN50018:2000 to which it is certified. 
(Note: EN60079-1 replaces EN50018) 
 
The user must ensure that the diametric clearance associated with the spigot joint at 
each end cover does not exceed 0.064mm and the gap between the face of each end 
cover and the body does not exceeed 0.038mm. 
 

  For replacement purposes the end cover fixing screws shall be of minimum grade A4-80 

stainless steel. 

 

  The cable entry device shall be suitably sealed to maintain IP66 rating. 

 
 

Summary of Contents for YA60BD















Reviews: