background image

FUNCTIONING

COMPONENTS LOCATION

Switching on

1) Check that the gas service tap is opened at the gasmeter and

main power is on.

2) Check that pressure in central heating system is above 0.7 bar

and below 2.5 bar with the pressure gauge 

18.

3) Open the gas tap 

by turning from right to left.

4) The boiler is now ready to use.

Central Heating

1) Turn selector switch 15 fully clockwise to position 

The green

"power on" indicator 

will light 20.

2) If the room thermostat (if fitted), the boiler temperature control

and the clock (if fitted) are all calling for heat, the orange

"burner on" indicator 

21 will light and the heating will be on.

Note: If the boiler has been turned off for some time the first
attempt to light it may result in a lockout 

.

22 If this happens

press the reset button 23 and the boiler will light.

Control panel

BRITONY SYSTEM FUNCTIONAL DIAGRAM

C

23

22

18

21

20

17

15

3

50

47

45

51

49

43

40

39

37

34

36

35

29

32

30

31

28

27

24

14

13

12

1

3

5

7

49

12

40

11

39

36

29

26

51

24

50

46

10

33

45

35

13

34

14

25

K

Summary of Contents for BRITONY System II 100













Reviews: