Canarm 9209, Installation And Maintenance Instructions

Page: 2 / 2

9200 SERIES BLOWERS
OCTOBER 2017 Page 2 of 2
ELECTRICAL
Connect motor in accordance with applicable codes. Provide properly sized motor overload protection to protect motor against electrical
faults and system changes. Confirm proper motor rotation on start-up.
MAINTENANCE
Inspect periodically for mounting rigidity. Verify belt for wear and tension and adjust as required. Inspect wheel for any dust accumulation
and clean as indicated.
CAUTION - DO NOT DISLODGE BALANCING CLIPS. CHECK SET SCREW FOR TIGHTNESS.
LUBRICATION
Insert bearings with sealed in lubricant are used on all 9200 series models up to 9215. No further lubrication is required. Models 9218 and
9220 use cast iron, pillow block, sealed type bearings. Re-lubrication is unnecessary under most operating conditions. If lubrication is
required lubricant should be compatible to Esso Beacon #325.
NOTE: For fractional HP applications “4L” belts may be substituted by adding 2” to the specified “B” belt. EG. B50 belt = 4L52
"9200" SERIES BLOWER BELT LENGTH SELECTION
TABLE
5" 6" 7" 8" 9" 10" 625
824-1125
RPM
680-929
RPM
580-792
RPM
505-690
RPM
447-611
RPM
401-548
RPM
533-455
RPM
9209 4L36 4L38 4L40 4L42 4L44 4L45 --
9210 4L38 4L40 4L41 4L43 4L45 4L47 --
BELT LENGTH BASED
ON MOTOR FRAME
3 1/4” DIA. ZINC DIE CAST BLOWER PULLEY - DIA. & RPM RANGE
BLOWER
MODEL
48 FRAME
9209 92 1 0 92 1 2 92 1 5 92 1 8 9220
HB 77 T 756-568 B 50 B 55 B 63 B 68
HB 87 T 667-500 B 52 B 57 B 65 B 70
HB 97 T 596-447 B 54 B 59 B 67 B 72
HB 107 T 538-404 B 55 B 61 B 68 B 74
HB 117 T 491-368 B 57 B 62 B 70 B 75
HB 127 T 452-339 B 59 B 64 B 72 B 77
HB 137 T 418-314 B 61 B 66 B 74 B 79
HB 157 T 364-273 -- B 70 B 77 B 82
HB 187 T 304-228 -- -- B 83 B 88
HB 47 T 1630-1232 B 36 B 38 -- -- -- --
HB 57 T 1329-1005 B 38 B 40 -- -- -- --
HB 67 T 1121-848 B 39 B 41 -- -- -- --
HB 77 T 969-733 B 41 B 43 B 50 B 53 B 65 --
HB 87 T 854-645 B 43 B 45 B 51 B 55 B 67 B 72
HB 97 T 763-577 B 45 B 47 B 53 B 56 B 68 B 74
HB 107 T 690-521 B 46 B 49 B 55 B 58 B 70 B 75
HB 117 T 629-476 B 48 B 50 B 56 B 60 B 72 B 77
HB 127 T 578-437 B 50 B 52 B 58 B 61 B 73 B 78
HB 137 T 535-404 B 52 B 54 B 60 B 63 B 75 B 80
HB 157 T 466-352 B 56 B 58 -- B 67 B 79 B 84
HB 187 T 390-295 B 63 B 64 -- -- -- --
HB 77 T 1253-1017 -- -- B 52 B 55 B 67 --
HB 87 T 1104-896 -- -- B 53 B 57 B 69 B 74
HB 97 T 1005-815 -- -- B 55 B 58 B 70 B 76
HB 107 T 907-750 -- -- B 57 B 60 B 72 B 77
HB 117 T 828-686 -- -- B 58 B 62 B 74 B 79
HB 127 T 756-618 -- -- B 60 B 63 B 75 B 80
HB 137 T 697-575 -- -- B 62 B 65 B 77 B 82
HB 157 T 616-509 -- -- -- B 69 B 81 B 86
HB 187 T 522-435 -- -- -- -- B 86 B 91
HB 87 T 1104-896 -- -- B 55 B 58 B 71 --
HB 97 T 1005-815 -- -- B 57 B 60 B 72 --
HB 107 T 907-750 -- -- B 58 B 62 B 74 B 79
HB 117 T 828-686 -- -- B 60 B 63 B 75 B 80
HB 127 T 756-618 -- -- B 62 B 65 B 77 B 82
HB 137 T 697-575 -- -- B 64 B 67 B 79 B 84
HB 157 T 616-509 -- -- -- B 70 B 82 B 87
HB 187 T 522-435 -- -- -- -- B 88 B 92
11 . 0 X 2 B 939-780 -- -- ( 2 ) B 78 ( 2 ) B 83
12 . 4 X 2 B 830-700 -- -- ( 2 ) B 80 ( 2 ) B 85
13 . 6 X 2 B 759-631 -- -- ( 2 ) B 82 ( 2 ) B 87
15 . 4 X 2 B 682-574 -- -- ( 2 ) B 85 ( 2 ) B 90
18 . 4 X 2 B 569-486 -- -- ( 2 ) B 91 ( 2 ) B 95
20 . 0 X 2 B 516-429 -- -- ( 2 ) -- --
11 . 0 X 2 B 924-764 -- -- -- -- -- ( 2 ) BX 85
12 . 4 X 2 B 817-678 -- -- -- -- -- ( 2 ) --
13 . 6 X 2 B 745-618 -- -- -- -- -- ( 2 ) BX 90
15 . 4 X 2 B 657-545 -- -- -- -- -- ( 2 ) BX 93
18 . 4 X 2 B 551-456 -- -- -- -- -- ( 2 ) BX 97
20 . 0 X 2 B 507-419 -- -- -- -- -- ( 2 ) BX 100
254 T FRAM E
NOTE: A DD . 35 TO DOUB L E
G R OOVE PU LL EY
M ODE L NU M BE R F O R O.D.
DI M ENSION
EG. 11 . 0 X 2 B = 11 . 35 O.D.
DOUB L E G R OOVE
B L OWER MODE L
RPM
RA N GE
L OWER PU LL E Y
CAS T I RO N
D8600
O.D. 6"
2 LV P48B60A
O.D. 6.5"
NOTE: B L OWE R PU LL EY M ODE L
NU M BE R SPECI F IES O.D.
EG. HB 47 T = 4 . 7 " O.D.
8550
O.D. 5.35"
M ODE L S 9209 & 9210
48 FRAM E
( A DD 1 ” F O R 56 FRAM E)
B ALA NCE 143 T, 145 T FRAM E
143 T & 145 T FRAM E
182 T, 184 T FRAM E
(DEDUCT 2 ” F O R 56 ,
143 T & 145 T)
182 T & 184 T FRAM E
(DEDUCT 2 ” F O R 56 , 143 T
& 145 T)
213 T, 215 T FRAM E
8325
O.D. 3.25"
IVL 44
O.D. 4. 1 5"
8400
O.D. 4. 1 5"
MO T OR PU LL E Y
CAS T I RO N
BE LT L E N G TH
BASED O N MO T OR FRAME
WWW.CANARM.COM