background image

EN-Rev IM/IEC-AM-EN/3.6 Copyright © March 2017. Canadian Solar Inc.

4 | 

·  If the disconnects and Over Current Protection 

Device (OCPD)'s cannot be opened or the inverter 
cannot be powered down, cover the fronts of 
modules in the PV array with an opaque material 
to stop the production of electricity when installing 
or working on a module or wiring.

· 

Do not

 

use or install broken modules.

·  Contact with module surfaces or frames may cause 

electric shock if the front glass is broken or the 
backsheet is torn.

·  The PV module does not contain any serviceable parts. 

Do not attempt to repair any part of the module. 

·  Keep the junction box cover closed at all times.

· 

Do not

 

disassemble a module or remove any 

  module part.

· 

Do not

 artificially concentrate sunlight on a module.  

· 

Do not

 

connect or disconnect modules when current 

from the modules or an external source is present.

3.0  

MECHANICAL / ELECTRICAL 

SPECIFICATIONS

Module electrical ratings are measured under 
Standard Test Conditions (STC) of 1000 W/m

2

 

irradiance, with an AM1.5 spectrum, and a cell 
temperature of 25°C. Detailed electrical and 
mechanical characteristics of Canadian Solar Inc. 
crystalline silicon PV modules can be found in 
our Installation Manual Annex ( Section Annex C: 

Module Specifications) on 

www.canadiansolar.com.

 

Main electrical characteristics at STC are also stated 
on each module label. Please refer to the datasheet 
or the product nameplate for the maximum system 
voltage.

Under certain conditions, a module may produce 
more current or voltage than under its Standard Test 
Condition's rated power. As a result, the module 
short-circuit current at under STC should be 
multiplied by 1.25, and a correction factor should 
be applied to the open-circuit voltage (see Table 1 
below), when determining component ratings and 
capacities. Depending on your local regulations, an 
additional 1.25 multiplier for the short-circuit current 
(giving a total multiplier of 1.56) may be applicable 
when sizing conductors and fuses. 

Lowest Expected Ambient Temperature (°C/°F)

Correction Factor

24 to 20 / 76 to 68

1.02

19 to 15 / 67 to 59

1.04

14 to 10 / 58 to 50

1.06

9 to 5 / 49 to 41

1.08

4 to 0 / 40 to 32
-1 to -5 / 31 to 23

1.10
1.12

-6 to -10 / 22 to 14

1.14

-11 to -15 / 13 to 5

1.16

-16 to -20 / 4 to -4

1.18

-21 to -25 / -5 to -13

1.20

-26 to -30 / -14 to -22

1.21

-31 to -35 / -23 to -31

1.23

-36 to -40 / -32 to -40

1.25

Table 1: Low temperature correction  
factors for open-circuit voltage

Summary of Contents for CS6A-M












Reviews: