background image

21

ENGLISHENGLISH

Installation, use and maintenance instruction manual

  

 

 

Ed. 05/2018 Rev. 00  

GAS CONNECTION PROCEDURE

The appliance is supplied with a gas train with a 
smooth end section and free for at least 30 mm, fit 
to house suitable press fittings. Proceed as follows 
to perform the gas connection:

Please note:

 the fittings are not supplied with the product. Their 

supply and connection are the responsibility of the installer.

EQUIPMENT REQUIRED

step

action

1

Connect the Ø 8 mm pipe to the clamp fitting of 
the gas distribution network.

ATTENTION!
During the installation and connection 
operations, the gas supply pipe of the 
appliance must not be subject to twisting, 
traction or any other mechanical stress 
which could jeopardise tightness and 
strength. 

After having connected the appliance to the gas mains, check tightness of the fittings with soap and water.

ATTENTION!
It is absolutely prohibited to use naked flames to check tightness and to put the device into 
service! If the test is satisfactory, light all the burners to make sure that the flame is regular 
and stable.

ELECTRICAL CONNECTION (only for IGN version)

IGN versions are equipped with a low voltage spark generator (12 V DC) to light the burners, generally 
installed on the metal bracket at the bottom of the hob unit. To connect the generator to the local power 
mains, proceed as follows:

step

action

-       +

12 V DC

1

1  Power cable positive pole
2  Power cable negative pole
3  Connection cable generator 

button

4  Glow plugs fast-on housing
5  Glow plugs fast-on 

connectors

6  12V DC (+ -) power supply 

fast-on connectors

2

3

4

4

4

5

5

5

6

1

Connect the free end of the black conductor (-) 
to the negative pole of the terminals of the mains 
or of a battery.

2

Connect the free end of the black conductor (+) 
to the positive pole of the terminals of the mains 
or of a battery.

ATTENTION!
Any type of connection of the appliance 
to a power mains other than 12V and in 
direct current (DC) is strictly prohibited. 
Any other connection can pose a severe 
danger for the user of the appliance and 
cause irreversible damage to the device 
itself.

Summary of Contents for FL1400





































Reviews: