Can Industrial 407021P Assembly Manual Download Page 2

SPECIFICATION

Width: 12.2m

Height: 6.4m

Length: 21.35m

Door dimension: W4xH4m

IMPORTANT----READ MANUAL FIRST

Improper site preparation, assembly and maintenance may invalidate warranty and cause unnecessary and costly
mistakes. If you have any questions contact your local dealer.

For User Friendly assembly we have identified each individual component with the part code as indicated in the
parts list. Please refer to the part code numbers and drawing to ensure problem free assembly.

It’s necessary to tighten the roof fabric enough to avoid

hammocks

on the roof and also re-tighten once or twice

again after a few months of use. This is important when assembly in cold weather (autumn and winter) because the
fabric is stiff then and when we got the sun and warm weather afterwards it will make the fabric

slack

again

and need to be re-tighten before next winter.

It’s

the owners responsibility

to take of snow immediately if not slide of by itself.

READ ALL INSTRUCTIONS BEFORE ASSEMBLY

1. Keep work area clean. Cluttered areas invite injuries. Do not set up near snow drifts, in slippery places, in high
winds, or wet location.

2. Keep children away. All children should be kept away from the work area. Be aware of personal safety. Be
careful not to pinch fingers with clips and tubes when assembling: when using makes sure there is adequate
ventilation for exhaust and other dangerous fumes.

3. Do not over reach. Keep proper footing and balance at all times.

4. Do not assemble if under the influence of alcohol or drugs. Read warning labels on prescription to determine if
your judgment or reflexes are impaired while taking drugs. IF there is any doubt, do not assemble.

5. Be aware of possible windy conditions; fasten the base in concrete if these situations may occur. Remove the
cover during hurricane.

6. Be careful with power and heat sources. Do not keep heat sources near the tarpaulin. Do not expose to open
flame.

7.Be aware of personal safety during assembly and use .Be careful not to pinch fingers with clips and tubes when
assembling when using makes sure there is adequate ventilation for exhaust and other dangerous fumes.

Summary of Contents for 407021P












Reviews: