5
The order of the setup goes as follows:
Setting item blinking at 1s frequency.
Under default state, press and hold "MODE"(1a) for 4 seconds to enter setting in sequence, the time will start to flash.
2.1 Time Setting
Into the probe insert 2x AAA battery.
Insert the battery (3xAAA) into the device or connect adapter after a few seconds, LCD will light up, after a beep, it enters default mode.
2. Clock 3.Inside temperature 4. Date 5. Outside temperature 6. Probe 8. Weather Forecast 9. Indoor humidity % 10. Outdoor humidity % 11. High/ Low
alerts indicator 13. Time alarms 1,2
2. Operation Instruction
1. Control panel: Buttons 1.a. MODE, 1b.UP, 1.c. DOWN, 1.d. ALARM, Buttons 1e. CHANNEL, 1f. SNOOZE/LIGHT
，
1.g. ALERTS
Description of the device. ( Weather Station)
Display:
batteries inside.
Press “UP”(1b) key, the data goes up one step; press and hold for 2 seconds or more, it will go ahead at 8 steps per second speed.
Press the “DOWN”(1c) key, the value goes down one step; press and hold for 2 seconds, go back at 8 steps per second speed.
After setting, press "MODE"(1a) to confirm/exit.
After 10 seconds of not pressing any button, the device will exit the change mode and will save all current settings that were changed to that point.
Hour→ Minute→ Year→ Month→ Day→ Week Language→ Exit
2.2 Alarm Setting
To set the alarm press the “MODE”(1a) button once. The text AL 1 will appear next to the date and the last alarm setting will appear.
Press and hold “MODE”(1a) Button for 2 seconds and the first digit of the setting will start to Flash.
Setting item blinking at 1s frequency.
Press “UP”(1b) key, the value goes ahead one step; press and hold for 2 seconds, go ahead at an 8 step per second speed.
Press “DOWN”(1c) once and back; press and hold for 2 seconds, go back at an 8 step per second speed.
After setting, press "MODE"(1a) to confirm and exit.
After 10 seconds of not pressing any button, the device will exit the change mode and will save all current settings that were changed to that point.
AL2 Setting is the same as the AL1 setting.
Setting in sequence: AL1 Hour→AL1 Minute →Exit
2.3 Alarm ON/OFF
* Under default mode, press "ALARM"(1d) to turn on/off the alarm in sequence:
AL1 ON→AL2 ON→AL1 and AL2 ON→AL1 and AL2 OFF
When the alarm turns on you can press. Alerts button to shut it off. You can also press the “Snooze”(1f) button. It will turn off again after the *Snooze* time
runs out up to 20 minutes.
To change the “Snooze” time duration press and hold the “Snooze/Light”(1f) button for 4 seconds and using the “UP”(1b) and “DOWN”(1c) keys change the
time up to 20 minutes.
After 2 minutes of working the alarm will shut down of its own accord.
During the alarm, the corresponding AL1 or AL2 icon will flash.
When in snooze mode, corresponding AL character will flash.
To change the backlight strength press “SNOOZE/LIGHT”(1f) once. The device has 3 settings. 1. Maximum backlight 2. Minimum backlight 3. No backlight
If the alarm time for both AL1 and AL2 is the same. Only AL1 will flash when the time has been reached.
When one alarm is on snooze and the other alarm turns on the device will still turn on and alarm us.
You can turn on the snooze function without limit.
* Snooze could be repeated all the time.
The alarm has 3 settings.
a.0-10 seconds after the alarm starts, the device will make a noise 1 time per second
b.10-20 seconds after the alarm starts, the device will make a noise 2 time per second
c. Over 20 seconds after the alarm starts, the device will make a noise 4 time per second
2.5 Temperature and Humidity Function
* Out of the indoor and outdoor temperature display, the low-end displays “Lo”, the high-end displays “Hi”. You can check the lowest and highest recorded
temperatures by pressing the „Alerts”(1g) briefly to cycle between them. The device picks up problems that work on up to 3 radio channels.
* Under normal mode, press “CHANEL”(1e) key to switch outdoor temperature and humidity display, switch in sequence: CH1 temperature and humidity→
CH2 temperature and humidity→CH3 temperature and humidity→ CH2 temperature and humidity→ CH1 temperature and humidity (cycle display).
To change the channel of the Probe open the Probe and in the middle, there is a switch with 1,2,3 next to it. By sliding the switch up and down change the
number of the channel the probe is using
2.6 Temperature Alert Setting
* Under time mode, press the “ALERTS(1g)” key to check temperature alert for both highest and lowest indoor and outdoor temperature.
* Under temperature alert mode, press “UP”(1b) key or “DOWN”(1c) key to turn alarm on/off. Once turned ON, next to the corresponding alarm symbol will
appear.
* Under time(default) mode, press and hold “ALERTS”(1g) key for 4 seconds to check temperature alert both highest and lowest outdoor and indoor
temperature in sequence: highest outdoor temperature→ lowest outdoor temperature→ highest indoor temperature→ lowest indoor temperature→
exit
* Indoor temperature upper limit: 50C, lowest limit: 0C.
* Outdoor temperature upper limit: 70C, lowest limit: -40C.
* Setting item blinking at 1s frequency.
* Press “UP”(1b), value go ahead one step; press and hold for 4 seconds, go ahead at an 8 step per second speed.
* Press “DOWN”(1c) key, the value goes back one step; press and hold for 4 seconds, go back at an 8 step per second speed.
* After setting, press "ALERTS"(1g) to confirm.
* After 10 seconds of not pressing any button the device will exit the change mode and will save all current settings that were changed till that point.
DCF:
* After power-on or reset, after testing temperature and humidity the device will start receiving DCF for 3 minutes automatically.
* Press and hold “DOWN” (1c) key for 2 seconds to enter into DCF receiving.
* Daily auto receiving:
DCF receiving automatically at 1:00 AM, 2:00 AM, 3:00 AM every day, if the device fails to receive Radio Command until 3:00 AM, then will try again at 4:00
am or 5:00 am.
TECHNICAL DATA
Station:100-240V 50/60Hz + 3xAAA
Probe:2xAAA
4
Summary of Contents for Premium CR 1174
Page 3: ...3 ...
