Campingaz ATTITUDE 2100 LX, Manual

Page: 14 / 17

14
1. Connect the regulator to your cylinder.
2. Check for leaks following the instructions in section f.
Do not pull or pierce the hose. Keep away from any parts
of the appliance that get hot. Check that the flexible hose
stretches out normally, without twisting or pulling. It should
be replaced if it is damaged or cracked, when required by
national regulations or at the end of its lifecycle.
Check for leaks following the instructions in paragraph f.
e) LID
Handle the lid carefully, especially during operation. Do
not lean over the base.
f) CHECKING FOR GAS LEAKS
1) Work outside, away from all sources of ignition. Do not
smoke.
2) Make sure the control knobs are in the “off” ( O )
position.
3) Connect the hose according to d) above.
4) Fit the regulator onto the gas cylinder in accordance
with its instructions.
5) Use a gas leak solution to test for leaks. Important:
never use a naked flame to check for gas leaks.
6) Apply the solution to the connections cylinder/ regulator/
hose/ apparatus (the control knobs should remain
closed: “off” position ( O ). Open the gas cylinder valve.
7) Bubbles in the gas leak solution indicate that there are
gas leaks.
8) The leak can be stopped by tightening any hose
connection or replacing any faulty component. The
barbecue must not be used until the leak is stopped.
9) Close the valve on the gas cylinder.
Important:
Check for leaks at least once per year and each time the
gas cylinder is replaced.
g) PRIOR TO USE
Never use the barbecue until the instructions have been
read carefully and understood. Also, make certain that:
- there are no leaks
- the venturi tubes are not blocked (example: spider
webs)
- the hose does not touch any components which may
get hot.
h) LIGHTING THE GRILL BURNERS
Read steps 1 to 5 before beginning with step 1.
1) Never light the barbecue with the lid closed, only
with the lid open.
2) Make sure the control knobs are in the “off” ( O )
position.
3) Open the gas cylinder valve.
4) Model Attitude 2100 LX (Abb. 5)
Press one of the 2 control knobs and turn it to the full
flow ( ) position, then immediately press the igniter
button ( ) until you hear the click. Hold it down for a
few seconds until it lights up. If the burner fails to light,
turn the control knob to the “off” position ( O ). Wait 5
minutes before repeating the operation.
Model Attitude 2100 EX (Abb. 6)
Press the control knob and then turn it counterclockwise
to the ignition position( ).
Keep pressing the button for the electronic ignition to
generate a spark.
Once the burner is lit, turn the control knob to the full
flow position ( ).
NOTE : NOTE: If the burner does not light after about
10 seconds, put the adjustment knob back in the OFF
( O ) position. Wait 5 minutes before repeating the
operation.
5) Once the burner is lit, the other burner ignites
automatically after putting the second control knob in
the full flow position ( ) without having to press the
automatic ignition button.
Important:
If the burner fails to light after the 2
nd
attempt, turn the
control knob to the “off” position ( O ) and check that the
burner outlets and inlet tube are not blocked. Check also
that the ignition battery is not drained.
i) GRILL BURNER-MANUAL LIGHTING
If the automatic ignition should fail to operate, turn the
control knob to the “off” position ( O ).
Remove the cooking grate.
Light a match and bring it close to a burner, then push in
and turn the corresponding control knob anti-clockwise to
the Full Flow position ( ).
Replace the cooking grate.
j) EXTINGUISHING THE GRILL
Return the control knobs to the “off” position ( O ), then
close the cylinder valve.
k) REPLACING THE GAS CYLINDER
- Always work in a well ventilated area and never in the
presence of a flame, spark or heat source.
- Return the control knobs in the “off” position (
O
) then
close the cylinder valve.
- Remove the regulator, check that the sealing joint is in
good condition.
- Put the full cylinder in place, refit the regulator, taking
care not to apply stress to the hose. Check for gas
leaks.
GB
(Abb. 5)
Hold it down for a
f the bur
2) Make sure the control knobs are in the “off” (
never use a naked flame to check for gas leaks.
6) A
hose/ apparatus (the control knobs should remain
closed: “off” position (
For r
efer
ence only
(Abb. 5) (Abb. 5)
ress one of the 2 control knobs and turn it to the full ress one of the 2 control knobs and turn it to the full
For r
efer
ence only
(Abb. 5) (Abb. 5)
ress one of the 2 control knobs and turn it to the full ress one of the 2 control knobs and turn it to the full
) position, then immediately press the igniter ) position, then immediately press the igniter
Hold it down for a Hold it down for a
For r
efer
ence only
ress one of the 2 control knobs and turn it to the full ress one of the 2 control knobs and turn it to the full
) position, then immediately press the igniter ) position, then immediately press the igniter
Hold it down for a Hold it down for a
For r
efer
ence only
(Abb. 5) (Abb. 5)
ress one of the 2 control knobs and turn it to the full ress one of the 2 control knobs and turn it to the full
) position, then immediately press the igniter ) position, then immediately press the igniter
) until you hear the click. ) until you hear the click.
For r
efer
ence only
For r
efer
ence only
For r
efer
ence only
1) Work outside, away from all sources of ignition. 1) Work outside, away from all sources of ignition. D D o not o not
2) Make sure the control knobs are in the “off” ( 2) Make sure the control knobs are in the “off” ( O O ) )
Connect the hose according to d) above. Connect the hose according to d) above.
4) Fit the regulator onto the gas cylinder in accordance 4) Fit the regulator onto the gas cylinder in accordance
with its instructions. with its instructions.
5) Use a gas leak solution to test for leaks. 5) Use a gas leak solution to test for leaks.
never use a naked flame to check for gas leaks. never use a naked flame to check for gas leaks.
pply the solution to the connections cylinder/ regulator/ pply the solution to the connections cylinder/ regulator/
hose/ apparatus (the control knobs should remain hose/ apparatus (the control knobs should remain
closed: “off” position ( closed: “off” position (
For r
efer
ence only
For r
efer
ence only
For r
efer
ence only
For r
efer
ence only
For r
efer
ence only
For r
efer
ence only
For r
efer
ence only
Model Attitude 2100 LX Model Attitude 2100 LX (Abb. 5) (Abb. 5)
ress one of the 2 control knobs and turn it to the full ress one of the 2 control knobs and turn it to the full
) position, then immediately press the igniter ) position, then immediately press the igniter
) until you hear the click. ) until you hear the click. Hold it down for a Hold it down for a
few seconds until it lights up. few seconds until it lights up. I I f the bur f the bur
turn the control knob to the “off” position ( turn the control knob to the “off” position (
minutes before repeating the operation. minutes before repeating the operation.
Model Attitude 2100 EX Model Attitude 2100 EX
Press the control knob and then turn it counterclockwise Press the control knob and then turn it counterclockwise
to the ignition position( to the ignition position(
Keep pressing the button for the electronic ignition to Keep pressing the button for the electronic ignition to
For r
efer
ence only
ress one of the 2 control knobs and turn it to the full ress one of the 2 control knobs and turn it to the full
) position, then immediately press the igniter ) position, then immediately press the igniter
) until you hear the click. ) until you hear the click.
few seconds until it lights up. few seconds until it lights up.
For r
efer
ence only
) until you hear the click. ) until you hear the click.
few seconds until it lights up. few seconds until it lights up.
turn the control knob to the “off” position ( turn the control knob to the “off” position (
minutes before repeating the operation. minutes before repeating the operation.
For r
efer
ence only
turn the control knob to the “off” position ( turn the control knob to the “off” position (
minutes before repeating the operation. minutes before repeating the operation.
Model Attitude 2100 EX Model Attitude 2100 EX
minutes before repeating the operation. minutes before repeating the operation.
For r
efer
ence only
For r
efer
ence only
minutes before repeating the operation. minutes before repeating the operation.
Model Attitude 2100 EX Model Attitude 2100 EX
Press the control knob and then turn it counterclockwise Press the control knob and then turn it counterclockwise
For r
efer
ence only
For r
efer
ence only
For r
efer
ence only
For r
efer
ence only
Press the control knob and then turn it counterclockwise Press the control knob and then turn it counterclockwise
For r
efer
ence only
D D o not o not
2) Make sure the control knobs are in the “off” ( 2) Make sure the control knobs are in the “off” ( O O
For r
efer
ence only
o not o not
For r
efer
ence only
1) Work outside, away from all sources of ignition. 1) Work outside, away from all sources of ignition.
2) Make sure the control knobs are in the “off” ( 2) Make sure the control knobs are in the “off” (
For r
efer
ence only
2) Make sure the control knobs are in the “off” ( 2) Make sure the control knobs are in the “off” (
Connect the hose according to d) above. Connect the hose according to d) above.
For r
efer
ence only
2) Make sure the control knobs are in the “off” ( 2) Make sure the control knobs are in the “off” (
Connect the hose according to d) above. Connect the hose according to d) above.
4) Fit the regulator onto the gas cylinder in accordance 4) Fit the regulator onto the gas cylinder in accordance
For r
efer
ence only
2) Make sure the control knobs are in the “off” ( 2) Make sure the control knobs are in the “off” (
For r
efer
ence only
Connect the hose according to d) above. Connect the hose according to d) above.
4) Fit the regulator onto the gas cylinder in accordance 4) Fit the regulator onto the gas cylinder in accordance
5) Use a gas leak solution to test for leaks. 5) Use a gas leak solution to test for leaks.
For r
efer
ence only
Connect the hose according to d) above. Connect the hose according to d) above.
4) Fit the regulator onto the gas cylinder in accordance 4) Fit the regulator onto the gas cylinder in accordance
For r
efer
ence only
4) Fit the regulator onto the gas cylinder in accordance 4) Fit the regulator onto the gas cylinder in accordance
5) Use a gas leak solution to test for leaks. 5) Use a gas leak solution to test for leaks.
never use a naked flame to check for gas leaks. never use a naked flame to check for gas leaks. For r
efer
ence only
5) Use a gas leak solution to test for leaks. 5) Use a gas leak solution to test for leaks.
never use a naked flame to check for gas leaks. never use a naked flame to check for gas leaks.
pply the solution to the connections cylinder/ regulator/ pply the solution to the connections cylinder/ regulator/
For r
efer
ence only
never use a naked flame to check for gas leaks. never use a naked flame to check for gas leaks.
pply the solution to the connections cylinder/ regulator/ pply the solution to the connections cylinder/ regulator/
hose/ apparatus (the control knobs should remain hose/ apparatus (the control knobs should remain
closed: “off” position ( closed: “off” position (
For r
efer
ence only
never use a naked flame to check for gas leaks. never use a naked flame to check for gas leaks.
A A pply the solution to the connections cylinder/ regulator/ pply the solution to the connections cylinder/ regulator/
hose/ apparatus (the control knobs should remain hose/ apparatus (the control knobs should remain
closed: “off” position ( closed: “off” position (
For r
efer
ence only
(Abb. 5) (Abb. 5)
ress one of the 2 control knobs and turn it to the full ress one of the 2 control knobs and turn it to the full
) position, then immediately press the igniter ) position, then immediately press the igniter
) until you hear the click. ) until you hear the click. Hold it down for a Hold it down for a
f the bur f the bur
For r
efer
ence only
ress one of the 2 control knobs and turn it to the full ress one of the 2 control knobs and turn it to the full
) position, then immediately press the igniter ) position, then immediately press the igniter
) until you hear the click. ) until you hear the click.
few seconds until it lights up. few seconds until it lights up. IIf the bur f the bur
turn the control knob to the “off” position ( turn the control knob to the “off” position (
For r
efer
ence only
) until you hear the click. ) until you hear the click.
few seconds until it lights up. few seconds until it lights up.
turn the control knob to the “off” position ( turn the control knob to the “off” position (
minutes before repeating the operation. minutes before repeating the operation.
For r
efer
ence only
) until you hear the click. ) until you hear the click.
few seconds until it lights up. few seconds until it lights up.
turn the control knob to the “off” position ( turn the control knob to the “off” position (
For r
efer
ence only
turn the control knob to the “off” position ( turn the control knob to the “off” position (
minutes before repeating the operation. minutes before repeating the operation.
Model Attitude 2100 EX Model Attitude 2100 EX
For r
efer
ence only
turn the control knob to the “off” position ( turn the control knob to the “off” position (
minutes before repeating the operation. minutes before repeating the operation.
For r
efer
ence only
For r
efer
ence only
minutes before repeating the operation. minutes before repeating the operation.
Model Attitude 2100 EX Model Attitude 2100 EX
Press the control knob and then turn it counterclockwise Press the control knob and then turn it counterclockwise
For r
efer
ence only
For r
efer
ence only
For r
efer
ence only
Press the control knob and then turn it counterclockwise Press the control knob and then turn it counterclockwise
to the ignition position( to the ignition position(
For r
efer
ence only
1) Work outside, away from all sources of ignition. 1) Work outside, away from all sources of ignition. D Do not o not
2) Make sure the control knobs are in the “off” ( 2) Make sure the control knobs are in the “off” ( O O ) )
For r
efer
ence only
D Do not o not
For r
efer
ence only
2) Make sure the control knobs are in the “off” ( 2) Make sure the control knobs are in the “off” (
Connect the hose according to d) above. Connect the hose according to d) above.
4) Fit the regulator onto the gas cylinder in accordance 4) Fit the regulator onto the gas cylinder in accordance
For r
efer
ence only
2) Make sure the control knobs are in the “off” ( 2) Make sure the control knobs are in the “off” (
Connect the hose according to d) above. Connect the hose according to d) above.
4) Fit the regulator onto the gas cylinder in accordance 4) Fit the regulator onto the gas cylinder in accordance
For r
efer
ence only
2) Make sure the control knobs are in the “off” ( 2) Make sure the control knobs are in the “off” (
For r
efer
ence only
Connect the hose according to d) above. Connect the hose according to d) above.
4) Fit the regulator onto the gas cylinder in accordance 4) Fit the regulator onto the gas cylinder in accordance
5) Use a gas leak solution to test for leaks. 5) Use a gas leak solution to test for leaks.
never use a naked flame to check for gas leaks. never use a naked flame to check for gas leaks. For r
efer
ence only
Connect the hose according to d) above. Connect the hose according to d) above.
4) Fit the regulator onto the gas cylinder in accordance 4) Fit the regulator onto the gas cylinder in accordance
For r
efer
ence only
with its instructions. with its instructions.
5) Use a gas leak solution to test for leaks. 5) Use a gas leak solution to test for leaks.
never use a naked flame to check for gas leaks. never use a naked flame to check for gas leaks.
pply the solution to the connections cylinder/ regulator/ pply the solution to the connections cylinder/ regulator/
hose/ apparatus (the control knobs should remain hose/ apparatus (the control knobs should remain
For r
efer
ence only
never use a naked flame to check for gas leaks. never use a naked flame to check for gas leaks.
pply the solution to the connections cylinder/ regulator/ pply the solution to the connections cylinder/ regulator/
hose/ apparatus (the control knobs should remain hose/ apparatus (the control knobs should remain
closed: “off” position ( closed: “off” position (
For r
efer
ence only
never use a naked flame to check for gas leaks. never use a naked flame to check for gas leaks.
6) 6) A Apply the solution to the connections cylinder/ regulator/ pply the solution to the connections cylinder/ regulator/
hose/ apparatus (the control knobs should remain hose/ apparatus (the control knobs should remain
closed: “off” position ( closed: “off” position (
For r
efer
ence only
For r
efer
ence only
For r
efer
ence only
never use a naked flame to check for gas leaks. never use a naked flame to check for gas leaks.
pply the solution to the connections cylinder/ regulator/ pply the solution to the connections cylinder/ regulator/
hose/ apparatus (the control knobs should remain hose/ apparatus (the control knobs should remain
(Abb. 6)
Press the control knob and then turn it counterclockwise
to the ignition position(
Keep pressing the button for the electronic ignition to
) position. Wait 5 minutes before repeating the
operation.
hose/ apparatus (the control knobs should remain
O ). O
Do not print Do not print Do not print
4) Fit the regulator onto the gas cylinder in accordance 4) Fit the regulator onto the gas cylinder in accordance
5) Use a gas leak solution to test for leaks. 5) Use a gas leak solution to test for leaks. Important: Important:
never use a naked flame to check for gas leaks. never use a naked flame to check for gas leaks.
pply the solution to the connections cylinder/ regulator/ pply the solution to the connections cylinder/ regulator/
hose/ apparatus (the control knobs should remain hose/ apparatus (the control knobs should remain
pen the gas cylinder valve. pen the gas cylinder valve.
Do not print Do not print Do not print Do not print Do not print
Model Attitude 2100 EX Model Attitude 2100 EX (Abb. 6) (Abb. 6)
Press the control knob and then turn it counterclockwise Press the control knob and then turn it counterclockwise
to the ignition position( to the ignition position(
Do not print Do not print
). ).
Keep pressing the button for the electronic ignition to Keep pressing the button for the electronic ignition to
generate a spark. generate a spark.
Once the burner is lit, turn the control knob to the full Once the burner is lit, turn the control knob to the full
flow position ( flow position (
Do not print
Once the burner is lit, turn the control knob to the full
Do not print Do not print
). ).
NOTE : NOTE : NOTE: If the burner does not light after about NOTE: If the burner does not light after about NOTE: If the burner does not light after about NOTE: If the burner does not light after about
10 seconds, put the adjustment knob back in the OFF 10 seconds, put the adjustment knob back in the OFF
( ( O O ) position. Wait 5 minutes before repeating the ) position. Wait 5 minutes before repeating the
operation. operation.
5 5 ) ) Once the burner is lit, the other burner ignites Once the burner is lit, the other burner ignites
Do not print Do not print
Press the control knob and then turn it counterclockwise Press the control knob and then turn it counterclockwise
Do not print Do not print
). ).
Keep pressing the button for the electronic ignition to Keep pressing the button for the electronic ignition to
Do not print
Press the control knob and then turn it counterclockwise Press the control knob and then turn it counterclockwise
Keep pressing the button for the electronic ignition to Keep pressing the button for the electronic ignition to
Do not print
to the ignition position( to the ignition position(
Keep pressing the button for the electronic ignition to Keep pressing the button for the electronic ignition to Keep pressing the button for the electronic ignition to Keep pressing the button for the electronic ignition to
Once the burner is lit, turn the control knob to the full Once the burner is lit, turn the control knob to the full
Do not print
to the ignition position( to the ignition position(
Keep pressing the button for the electronic ignition to Keep pressing the button for the electronic ignition to
Do not print
Keep pressing the button for the electronic ignition to Keep pressing the button for the electronic ignition to
generate a spark. generate a spark.
Once the burner is lit, turn the control knob to the full Once the burner is lit, turn the control knob to the full
). ).
Do not print
generate a spark. generate a spark.
Once the burner is lit, turn the control knob to the full Once the burner is lit, turn the control knob to the full
flow position ( flow position (
NOTE: If the burner does not light after about NOTE: If the burner does not light after about
Do not print
Once the burner is lit, turn the control knob to the full Once the burner is lit, turn the control knob to the full
flow position ( flow position (
Do not print
NOTE : NOTE : NOTE: If the burner does not light after about NOTE: If the burner does not light after about
10 seconds, put the adjustment knob back in the OFF 10 seconds, put the adjustment knob back in the OFF
) position. Wait 5 minutes before repeating the ) position. Wait 5 minutes before repeating the
Do not print
flow position ( flow position (
Do not print
NOTE : NOTE : NOTE: If the burner does not light after about NOTE: If the burner does not light after about
Do not print Do not print
( (
Do not print Do not print
Important: Important:
pply the solution to the connections cylinder/ regulator/ pply the solution to the connections cylinder/ regulator/
Do not print
never use a naked flame to check for gas leaks. never use a naked flame to check for gas leaks.
pply the solution to the connections cylinder/ regulator/ pply the solution to the connections cylinder/ regulator/
hose/ apparatus (the control knobs should remain hose/ apparatus (the control knobs should remain
pen the gas cylinder valve. pen the gas cylinder valve.
Do not print
hose/ apparatus (the control knobs should remain hose/ apparatus (the control knobs should remain
pen the gas cylinder valve. pen the gas cylinder valve.
Do not print Do not print Do not print
). ). O O pen the gas cylinder valve. pen the gas cylinder valve.
Do not print Do not print Do not print Do not print
pen the gas cylinder valve. pen the gas cylinder valve.
Do not print Do not print Do not print Do not print
Model Attitude 2100 EX Model Attitude 2100 EX (Abb. 6) (Abb. 6)
Press the control knob and then turn it counterclockwise Press the control knob and then turn it counterclockwise
to the ignition position( to the ignition position(
Do not print
Press the control knob and then turn it counterclockwise Press the control knob and then turn it counterclockwise
Do not print
). ).
Keep pressing the button for the electronic ignition to Keep pressing the button for the electronic ignition to
Do not print
to the ignition position( to the ignition position(
Do not print Do not print
Keep pressing the button for the electronic ignition to Keep pressing the button for the electronic ignition to Keep pressing the button for the electronic ignition to Keep pressing the button for the electronic ignition to Keep pressing the button for the electronic ignition to Keep pressing the button for the electronic ignition to
generate a spark. generate a spark.
Once the burner is lit, turn the control knob to the full Once the burner is lit, turn the control knob to the full
Do not print
to the ignition position( to the ignition position(
Keep pressing the button for the electronic ignition to Keep pressing the button for the electronic ignition to
Do not print
Keep pressing the button for the electronic ignition to Keep pressing the button for the electronic ignition to
generate a spark. generate a spark.
Once the burner is lit, turn the control knob to the full Once the burner is lit, turn the control knob to the full
).).
Do not print
Keep pressing the button for the electronic ignition to Keep pressing the button for the electronic ignition to
generate a spark. generate a spark.
Once the burner is lit, turn the control knob to the full Once the burner is lit, turn the control knob to the full
flow position ( flow position (
NOTE: If the burner does not light after about NOTE: If the burner does not light after about
Do not print
Once the burner is lit, turn the control knob to the full Once the burner is lit, turn the control knob to the full
flow position ( flow position (
Do not print
NOTE : NOTE : NOTE: If the burner does not light after about NOTE: If the burner does not light after about
10 seconds, put the adjustment knob back in the OFF 10 seconds, put the adjustment knob back in the OFF
) position. Wait 5 minutes before repeating the ) position. Wait 5 minutes before repeating the
Do not print
flow position ( flow position (
Do not print
NOTE : NOTE : NOTE: If the burner does not light after about NOTE: If the burner does not light after about
10 seconds, put the adjustment knob back in the OFF 10 seconds, put the adjustment knob back in the OFF
Do not print Do not print Do not print
(( O O
operation. operation.
Do not print Do not print
Important: Important:
pply the solution to the connections cylinder/ regulator/ pply the solution to the connections cylinder/ regulator/
Do not print Do not print
Important: Important:
pply the solution to the connections cylinder/ regulator/ pply the solution to the connections cylinder/ regulator/
Do not print
Important: Important:
never use a naked flame to check for gas leaks. never use a naked flame to check for gas leaks.
pply the solution to the connections cylinder/ regulator/ pply the solution to the connections cylinder/ regulator/
hose/ apparatus (the control knobs should remain hose/ apparatus (the control knobs should remain
pen the gas cylinder valve. pen the gas cylinder valve.
Do not print
hose/ apparatus (the control knobs should remain hose/ apparatus (the control knobs should remain
pen the gas cylinder valve. pen the gas cylinder valve.
Do not print Do not print Do not print
hose/ apparatus (the control knobs should remain hose/ apparatus (the control knobs should remain
pen the gas cylinder valve. pen the gas cylinder valve.
Do not print
hose/ apparatus (the control knobs should remain hose/ apparatus (the control knobs should remain
). ). O Open the gas cylinder valve. pen the gas cylinder valve.
Do not print Do not print Do not print Do not print
O Open the gas cylinder valve. pen the gas cylinder valve.
Do not print Do not print Do not print
Press the control knob and then turn it counterclockwise
Keep pressing the button for the electronic ignition to
Once the burner is lit, turn the control knob to the full
10 seconds, put the adjustment knob back in the OFF
) position. Wait 5 minutes before repeating the
control knob to the “off” position (
ubbles in the gas leak solution indicate that there are
仅供参考，请勿印刷
Keep pressing the button for the electronic ignition to Keep pressing the button for the electronic ignition to
Once the burner is lit, turn the control knob to the full Once the burner is lit, turn the control knob to the full
仅供参考，请勿印刷
Once the burner is lit, turn the control knob to the full Once the burner is lit, turn the control knob to the full
仅供参考，请勿印刷
Once the burner is lit, turn the control knob to the full Once the burner is lit, turn the control knob to the full
仅供参考，请勿印刷
Once the burner is lit, turn the control knob to the full Once the burner is lit, turn the control knob to the full
仅供参考，请勿印刷
Once the burner is lit, turn the control knob to the full Once the burner is lit, turn the control knob to the full
仅供参考，请勿印刷
NOTE: If the burner does not light after about NOTE: If the burner does not light after about
10 seconds, put the adjustment knob back in the OFF 10 seconds, put the adjustment knob back in the OFF
) position. Wait 5 minutes before repeating the ) position. Wait 5 minutes before repeating the
Once the burner is lit, the other burner ignites Once the burner is lit, the other burner ignites
automatically after putting the second control knob in automatically after putting the second control knob in
仅供参考，请勿印刷
10 seconds, put the adjustment knob back in the OFF 10 seconds, put the adjustment knob back in the OFF
) position. Wait 5 minutes before repeating the ) position. Wait 5 minutes before repeating the
Once the burner is lit, the other burner ignites Once the burner is lit, the other burner ignites
automatically after putting the second control knob in automatically after putting the second control knob in
the full flow position ( the full flow position (
仅供参考，请勿印刷
automatically after putting the second control knob in
仅供参考，请勿印刷
automatically after putting the second control knob in automatically after putting the second control knob in
仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷
ubbles in the gas leak solution indicate that there are ubbles in the gas leak solution indicate that there are
8) The leak can be stopped by tightening any hose 8) The leak can be stopped by tightening any hose
connection or replacing any faulty component. connection or replacing any faulty component.
barbecue must not be used until the leak is stopped. barbecue must not be used until the leak is stopped.
仅供参考，请勿印刷
operation. operation.
Once the burner is lit, the other burner ignites Once the burner is lit, the other burner ignites
automatically after putting the second control knob in automatically after putting the second control knob in
the full flow position ( the full flow position (
仅供参考，请勿印刷
the full flow position ( the full flow position (
仅供参考，请勿印刷
) without having to press the ) without having to press the
automatic ignition button. automatic ignition button.
Important: Important:
I I
仅供参考，请勿印刷
f the burner fails to light after the 2 f the burner fails to light after the 2
control knob to the “off” position ( control knob to the “off” position (
burner outlets and inlet tube are not blocked. Check also burner outlets and inlet tube are not blocked. Check also
仅供参考，请勿印刷
Keep pressing the button for the electronic ignition to Keep pressing the button for the electronic ignition to
Once the burner is lit, turn the control knob to the full Once the burner is lit, turn the control knob to the full
仅供参考，请勿印刷
Keep pressing the button for the electronic ignition to Keep pressing the button for the electronic ignition to
Once the burner is lit, turn the control knob to the full Once the burner is lit, turn the control knob to the full
仅供参考，请勿印刷
Keep pressing the button for the electronic ignition to Keep pressing the button for the electronic ignition to
Once the burner is lit, turn the control knob to the full Once the burner is lit, turn the control knob to the full
NOTE: If the burner does not light after about NOTE: If the burner does not light after about
仅供参考，请勿印刷
Keep pressing the button for the electronic ignition to Keep pressing the button for the electronic ignition to
仅供参考，请勿印刷
Once the burner is lit, turn the control knob to the full Once the burner is lit, turn the control knob to the full
仅供参考，请勿印刷
Once the burner is lit, turn the control knob to the full Once the burner is lit, turn the control knob to the full
NOTE: If the burner does not light after about NOTE: If the burner does not light after about
仅供参考，请勿印刷
Once the burner is lit, turn the control knob to the full Once the burner is lit, turn the control knob to the full
仅供参考，请勿印刷
NOTE: If the burner does not light after about NOTE: If the burner does not light after about
10 seconds, put the adjustment knob back in the OFF 10 seconds, put the adjustment knob back in the OFF
) position. Wait 5 minutes before repeating the ) position. Wait 5 minutes before repeating the
仅供参考，请勿印刷
Once the burner is lit, turn the control knob to the full Once the burner is lit, turn the control knob to the full
仅供参考，请勿印刷
Once the burner is lit, turn the control knob to the full Once the burner is lit, turn the control knob to the full
仅供参考，请勿印刷
NOTE: If the burner does not light after about NOTE: If the burner does not light after about
10 seconds, put the adjustment knob back in the OFF 10 seconds, put the adjustment knob back in the OFF
) position. Wait 5 minutes before repeating the ) position. Wait 5 minutes before repeating the
仅供参考，请勿印刷
NOTE: If the burner does not light after about NOTE: If the burner does not light after about
10 seconds, put the adjustment knob back in the OFF 10 seconds, put the adjustment knob back in the OFF
) position. Wait 5 minutes before repeating the ) position. Wait 5 minutes before repeating the
Once the burner is lit, the other burner ignites Once the burner is lit, the other burner ignites
automatically after putting the second control knob in automatically after putting the second control knob in
仅供参考，请勿印刷
) position. Wait 5 minutes before repeating the ) position. Wait 5 minutes before repeating the
Once the burner is lit, the other burner ignites Once the burner is lit, the other burner ignites
automatically after putting the second control knob in automatically after putting the second control knob in
仅供参考，请勿印刷
Once the burner is lit, the other burner ignites Once the burner is lit, the other burner ignites
仅供参考，请勿印刷
Once the burner is lit, the other burner ignites Once the burner is lit, the other burner ignites
automatically after putting the second control knob in automatically after putting the second control knob in
仅供参考，请勿印刷
Once the burner is lit, the other burner ignites Once the burner is lit, the other burner ignites
automatically after putting the second control knob in automatically after putting the second control knob in
the full flow position ( the full flow position (
automatic ignition button. automatic ignition button.
automatically after putting the second control knob in automatically after putting the second control knob in
仅供参考，请勿印刷
automatically after putting the second control knob in automatically after putting the second control knob in
the full flow position ( the full flow position (
仅供参考，请勿印刷
automatic ignition button. automatic ignition button.
仅供参考，请勿印刷
automatically after putting the second control knob in automatically after putting the second control knob in
the full flow position ( the full flow position (
仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷
Important: Important:
仅供参考，请勿印刷
f the burner fails to light after the 2 f the burner fails to light after the 2
control knob to the “off” position ( control knob to the “off” position (
仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷
ubbles in the gas leak solution indicate that there are ubbles in the gas leak solution indicate that there are
仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷
ubbles in the gas leak solution indicate that there are ubbles in the gas leak solution indicate that there are
仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷
ubbles in the gas leak solution indicate that there are ubbles in the gas leak solution indicate that there are
8) The leak can be stopped by tightening any hose 8) The leak can be stopped by tightening any hose
connection or replacing any faulty component. connection or replacing any faulty component.
仅供参考，请勿印刷
ubbles in the gas leak solution indicate that there are ubbles in the gas leak solution indicate that there are
仅供参考，请勿印刷
ubbles in the gas leak solution indicate that there are ubbles in the gas leak solution indicate that there are
仅供参考，请勿印刷
ubbles in the gas leak solution indicate that there are ubbles in the gas leak solution indicate that there are
gas leaks. gas leaks.
仅供参考，请勿印刷
ubbles in the gas leak solution indicate that there are ubbles in the gas leak solution indicate that there are
8) The leak can be stopped by tightening any hose 8) The leak can be stopped by tightening any hose
connection or replacing any faulty component. connection or replacing any faulty component.
仅供参考，请勿印刷
ubbles in the gas leak solution indicate that there are ubbles in the gas leak solution indicate that there are
8) The leak can be stopped by tightening any hose 8) The leak can be stopped by tightening any hose
connection or replacing any faulty component. connection or replacing any faulty component.
仅供参考，请勿印刷
ubbles in the gas leak solution indicate that there are ubbles in the gas leak solution indicate that there are
仅供参考，请勿印刷
Press the control knob and then turn it counterclockwise Press the control knob and then turn it counterclockwise
Keep pressing the button for the electronic ignition to Keep pressing the button for the electronic ignition to
Once the burner is lit, turn the control knob to the full Once the burner is lit, turn the control knob to the full
仅供参考，请勿印刷
Keep pressing the button for the electronic ignition to Keep pressing the button for the electronic ignition to
Once the burner is lit, turn the control knob to the full Once the burner is lit, turn the control knob to the full
仅供参考，请勿印刷
Keep pressing the button for the electronic ignition to Keep pressing the button for the electronic ignition to
Once the burner is lit, turn the control knob to the full Once the burner is lit, turn the control knob to the full
仅供参考，请勿印刷
Once the burner is lit, turn the control knob to the full Once the burner is lit, turn the control knob to the full
仅供参考，请勿印刷
NOTE: If the burner does not light after about NOTE: If the burner does not light after about
10 seconds, put the adjustment knob back in the OFF 10 seconds, put the adjustment knob back in the OFF
仅供参考，请勿印刷
Keep pressing the button for the electronic ignition to Keep pressing the button for the electronic ignition to
仅供参考，请勿印刷
Once the burner is lit, turn the control knob to the full Once the burner is lit, turn the control knob to the full
仅供参考，请勿印刷
Once the burner is lit, turn the control knob to the full Once the burner is lit, turn the control knob to the full
仅供参考，请勿印刷
NOTE: If the burner does not light after about NOTE: If the burner does not light after about
10 seconds, put the adjustment knob back in the OFF 10 seconds, put the adjustment knob back in the OFF
) position. Wait 5 minutes before repeating the ) position. Wait 5 minutes before repeating the
仅供参考，请勿印刷
NOTE: If the burner does not light after about NOTE: If the burner does not light after about
10 seconds, put the adjustment knob back in the OFF 10 seconds, put the adjustment knob back in the OFF
) position. Wait 5 minutes before repeating the ) position. Wait 5 minutes before repeating the
Once the burner is lit, the other burner ignites Once the burner is lit, the other burner ignites
automatically after putting the second control knob in automatically after putting the second control knob in automatically after putting the second control knob in automatically after putting the second control knob in
仅供参考，请勿印刷
) without having to press the ) without having to press the
NOTE: If the burner does not light after about NOTE: If the burner does not light after about
仅供参考，请勿印刷
) position. Wait 5 minutes before repeating the ) position. Wait 5 minutes before repeating the
operation. operation.
Once the burner is lit, the other burner ignites Once the burner is lit, the other burner ignites
automatically after putting the second control knob in automatically after putting the second control knob in
the full flow position ( the full flow position (
仅供参考，请勿印刷
automatically after putting the second control knob in automatically after putting the second control knob in
the full flow position ( the full flow position (
仅供参考，请勿印刷
the full flow position ( the full flow position (
仅供参考，请勿印刷
automatic ignition button. automatic ignition button.
仅供参考，请勿印刷
Once the burner is lit, the other burner ignites Once the burner is lit, the other burner ignites
automatically after putting the second control knob in automatically after putting the second control knob in
Once the burner is lit, the other burner ignites Once the burner is lit, the other burner ignites
仅供参考，请勿印刷
Once the burner is lit, the other burner ignites Once the burner is lit, the other burner ignites
automatically after putting the second control knob in automatically after putting the second control knob in
the full flow position ( the full flow position (
仅供参考，请勿印刷
automatically after putting the second control knob in automatically after putting the second control knob in
the full flow position ( the full flow position (
仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷
ubbles in the gas leak solution indicate that there are ubbles in the gas leak solution indicate that there are
仅供参考，请勿印刷
Important: Important:
仅供参考，请勿印刷
f the burner fails to light after the 2 f the burner fails to light after the 2
control knob to the “off” position ( control knob to the “off” position (
仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷
ubbles in the gas leak solution indicate that there are ubbles in the gas leak solution indicate that there are
仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷 仅供参考，请勿印刷
ubbles in the gas leak solution indicate that there are ubbles in the gas leak solution indicate that there are
8) The leak can be stopped by tightening any hose 8) The leak can be stopped by tightening any hose
connection or replacing any faulty component. connection or replacing any faulty component.
barbecue must not be used until the leak is stopped. barbecue must not be used until the leak is stopped.
仅供参考，请勿印刷
ubbles in the gas leak solution indicate that there are ubbles in the gas leak solution indicate that there are