Campbell T107, Instruction Manual

Page: 8 / 106

Table of Contents
2-29. Loosely Wire Tie Antenna Cable ...................................................... 39
2-30. Loosely Drape Antenna Cable over Back of Enclosure .................... 40
2-31. Slide Antenna Bracket U-Bolt around Back of the Pole ................... 41
2-32. Antenna Bracket Mounted to Pole ..................................................... 42
2-33. Mount Antenna Saddle Bracket ......................................................... 42
2-34. Yagi Antenna Mounted to Saddle Bracket ........................................ 43
2-35. Wire Tie Antenna Cable to Yagi Antenna and to Pole ...................... 44
2-36. Wire Tie Locations for Omni Antenna Installation ........................... 45
2-37. Base RF450 Installation .................................................................... 46
2-38. A Base Radio Installed in an Office .................................................. 46
2-39. Lightning Rod Bracket Installation ................................................... 47
2-40. Grounding to Lightning Rod Clamp .................................................. 48
2-41. Solar Panel Mounting and Cabling .................................................... 49
2-42. Side View of Solar Panel Shows Tilt Angle ...................................... 50
2-43. PS100 Battery Installation ................................................................. 51
2-44. PS100 to T107 Enclosure Wiring ...................................................... 51
2-45. Cabling Strapped to Wire Tie Harness .............................................. 52
2-46. Connector Cover in Place .................................................................. 53
2-47. Desiccant Installation ........................................................................ 54
4-1. Exploded View of HMP60-ETS (as shipped) ................................... 57
4-2. RF450 Front Side View ..................................................................... 61
4-3. Schematic of HMP60-ETS RH and Temperature Probe and
Connector Temp/RH ...................................................................... 64
4-4. Schematic of 034B-LC Wind Speed and Direction Probe and
Connector WS/WD ........................................................................ 65
4-5. Schematic of Gill WindSonic1-ET Wind Sensor, Soil Temperature
Sensor (107-LC or 108-LC), and Connector Temp/Sonic ............. 65
4-6. Schematic of CS305-ET Solar Radiation Sensor and Connector
Solar Radiation .............................................................................. 66
4-7. Schematic of TE525-ET Rain Sensor and Connector Rain
(Precip) .......................................................................................... 67
4-8. Schematic of 107-LC or 108-LC Temperature Probe or CS616-LC
Soil Volumetric Water Content Sensor and Connector Temp/
CS616 ............................................................................................ 68
4-9. Schematic of Connector SDI-12 ........................................................ 68
4-10. Schematic of Solar Panel and Connector Power ............................... 69
4-11. Schematic of Short Haul or Phone Modem and Connector
COMM ........................................................................................... 69
B-1. Environmental Enclosure with CH100, Power Cable, and
Battery Bracket ............................................................................ B-1
B-2. 24 Ahr Battery and Battery Cable ................................................... B-2
B-3. Enclosure Supply Kit ....................................................................... B-3
B-4. Strut Clamps in Brackets ................................................................. B-4
B-5. Both Strut Clamps and Brackets on T107 Pole ............................... B-5
B-6. Top Clamp Hook Side Up ............................................................... B-6
B-7. Enclosure Mounted on T107 Pole ................................................... B-7
B-8. Enclosure Locking Mechanism ....................................................... B-8
B-9. Mounted Solar Panel ....................................................................... B-9
B-10. Procedure for installing and connecting battery ............................ B-11
E-1. ET tower installation with step-down transformer ........................... E-1
Tables
4-1. CR1000 Lithium Battery Specifications ............................................ 59
4-2. Multi-Point Network LED Status ...................................................... 62
4-3. Gill WindSonic Diagnostic Codes ..................................................... 64
iv