5
www.chpower.com
GW4500
Getting To Know Your
Welder / Generator
Glossary of Terms
AC or Alternating Current -
electric
current that reverses direction
periodically. Sixty cycle current travels in
both directions sixty times per second.
Arc Length -
the distance from the
end of the electrode to the point where
the arc makes contact with the work
surface.
Base Metal -
the material to be
welded.
Butt Joint -
a joint between two
members aligned approximately in the
same plane.
Crater -
a pool, or pocket, that is
formed as the arc comes in contact with
the base metal.
DC or Direct Current -
electric current
which flows only in one direction.
The polarity (+ or -) determines which
direction the current is flowing.
DC Reverse Polarity -
occurs when the
electrode holder is connected to the
positive pole of the welding machine.
Reverse Polarity directs more heat
into melting the electrode rather than
the work piece. It is used on thinner
material.
DC Straight Polarity -
occurs when
the electrode holder is connected to the
negative pole of the welding machine.
With straight polarity more heat is
directed to the work piece for better
penetration on thicker material.
Electrode -
a coated metal wire having
approximately the same composition as
the material being welded.
Fillet Weld -
approximately a triangle
in cross-section, joining two surfaces at
right angles to each other in a lap, T or
corner joint.
Flux -
a coating, when heated, that
produces a shielding gas around the
welding area. This gas protects the
parent and filler metals from impurities
in the air.
Slag -
a layer of flux soot that
protects the weld from oxides and
other contaminants while the weld is
solidifying (cooling). Slag should be
removed after weld has cooled.
Spatter -
metal particles thrown from
the weld which cool and harden on the
work surface. Spatter can be minimized
by using a spatter resistant spray on the
work piece before welding.
Tack Weld -
weld made to hold parts in
proper alignment until final welds are
made.
Travel Angle -
the angle of the
electrode in the line of welding. It varies
from 5º to 45º depending on welding
conditions.
T Joint -
made by placing the edge of
one piece of metal on the surface of
the other piece at approximately a 90º
angle.
Undercut -
a condition that results
when welding amperage is too high.
The excessive amperage leaves a groove
in the base metal along both sides of
the bead which reduces the strength of
the weld.
Weld Pool or Puddle -
a volume of
molten metal in a weld prior to its
solidification as weld metal.
Weld Bead -
a narrow layer or layers of
metal deposited on the base metal as
the electrode melts. Weld bead width
is typically twice the diameter of the
electrode.
Work Angle -
the angle of the
electrode from horizontal, measured at
right angles to the line of welding.
Flux Cored Arc Welding (FCAW) -
also called Gasless, is a welding process
used with a wire-feed welding machine.
The weld wire is tubular with flux
material contained inside for shielding.
Gas Metal Arc Welding (GMAW) -
also called MIG, is a welding process
used with a wire feed welding machine.
The wire is solid and an inert gas is used
for shielding.
Gas Tungsten Arc Welding (GTAW) -
also called TIG, is a welding process used
with welding equipment with a high
frequency generator. The arc is created
between a non-consumable tungsten
electrode and the work piece. Filler
metal may or may not be used.
Lap Joint -
a joint between two
overlapping members in parallel planes.
Open Circuit Voltage (OCV) -
the
voltage between the electrode and the
work clamp of the welding machine
when no current is flowing (not
welding). The OCV determines how
quickly the arc is struck.
Overlap -
occurs when the amperage is
set too low. In this instance, the molten
metal falls from the electrode without
actually fusing into the base metal.
Porosity -
gas pockets, or cavities,
formed during weld solidification. They
weaken the weld.
Penetration -
the depth into the work
piece that has been heat effected by
the arc during the welding process. A
good weld achieves 100% penetration
meaning that the entire thickness of
the work piece has been heated and
resolidified. The heat effected area
should be easily seen on the opposite
side of the weld.
Shielded Metal Arc Welding
(SMAW) -
also called Stick, is a welding
process that uses a consumable
electrode to support the arc. Shielding
is achieved by the melting of the flux
coating on the electrode.
