background image

Airless Paint Sprayers

7

Operating Instructions and Assembly Instructions 

Turn Prime/ Spray 

Control

to PRIME

(knob is horizontal)

Turn Pressure 

to HIGH  

(completely clockwise)

www.chpower.com

4

Use Finger to 

Check Inlet Valve

1

Starting Instructions

While Pulling Trigger, 

Direct Fluid Stream Along 

Inside of Bucket

9

Power Switch 

Location

6

Attach 

Suction 

Assembly

3

Tip in 

CLEANING 

Position

8

7

Turn Prime/ Spray 

Control

to SPRAY

(knob is vertical)

5

Preparation (Continued)

DO NOT ATTACh ThE SUCTION 
ASSEmbly UNTIl INSTrUCTED TO DO 
SO IN STEP 3.

1.  Remove inlet valve cap and with 

your smallest finger, push on inlet 
valve stem to ensure it moves freely.

2.   Push outlet prime button three 

times to ensure outlet valve is 
moving freely.

3.   Attach suction assembly and bypass 

tube securely and place both suction 
and bypass tubes in cleaning solvent.

4.   Turn pressure to HIGH (completely 

clockwise).

5.  Turn prime/spray control to the 

PRIME position.

6.  Turn power switch to the ON 

position. In a few seconds, cleaning 
solvent will begin to move up 
through the tube. Allow the fluid to 
circulate for one minute to ensure 
all air has been exhausted from the 
pump.

7.  Turn prime/spray control to SPRAY 

position. Watch for any fluid leaks 
(See Troubleshooting Chart if leaks 
occur).

NOTE:

  If unit is building pressure 

properly, the pump should produce a 
knocking sound, which indicates it has 
reached its hydraulic relief pressure.
8.  When flushing the system with 

cleansing fluid (either prior to 
use with paint or during cleaning 
process) the spray tip can remain in 
the CLEAN position.

9.  Point spray gun into an empty waste 

bucket and pull trigger. To reduce 
splashing, direct the fluid stream 
along the inside of the bucket wall 
and well above the fluid level.

2

Push Outlet 

Prime Button

Summary of Contents for PS250B

























Reviews: