background image

Airless Paint Sprayers

Operating Instructions and Assembly Instructions 

Safety Guidelines

ImPOrTANT SAFETy INSTrUCTIONS
SAvE ThESE INSTrUCTIONS

This manual contains information 
that is very important to know 
and understand. This information 
is provided for SAFETY and to 
PREVENT EQUIPMENT PROBLEMS. 
To help recognize this information, 
observe the following symbols. 

 

Danger indicates  

  an imminently 

hazardous situation which, if not 
avoided, will result in death or serious 
injury.
 

warning indicates  

  a potentially 

hazardous situation which, if not 
avoided, coulD result in death or 
serious injury.
 

caution indicates a  

  potentially 

hazardous situation which, if not 
avoided, MAY result in minor or 
moderate injury.
 

Notice indicates  

  important 

information, that if not followed, MAY 
cause damage to equipment.

Unpacking

After unpacking the unit, inspect 
carefully for any damage that may 
have occurred during transit. Make 
sure to tighten fittings, bolts, etc., 
before putting unit into service.

 

Do not operate  

  unit if damaged 

during shipping, handling or use. 
Damage may result in bursting and 
cause injury or property damage.

General Safety Information

CAlIFOrNIA PrOPOSITION 65

 

This product or its  

  power cord may 

contain chemicals, including lead, 
known to the State of california to 
cause cancer and birth defects or other 
reproductive harm. wash hands after 
handling.

GENErAl SAFETy

1.  SAVE THESE 

INSTRUCTIONS - To 
reduce the risks of fire 
or explosion, electrical 
shock, and injury to 
persons, read and understand 
all instructions included in this 
manual. Be thoroughly familiar 
with the controls and the proper 
use of the equipment.

2.  Always wear a mask 

or respirator and 
eye protection when 
painting. Be certain 
mask or respirator 
will provide necessary protection 
against inhalation of harmful 
vapors.

3.  Keep visitors away and NEVER 

allow children or pets in the work 
area.

4.   Do not smoke or eat when spraying 

paint, insecticides, or other 
flammable substances.

5.  Always work in a clean 

environment. To avoid injury and 
damage to the workpiece, do not 
aim the spray gun at any dust or 
debris.

6.  When spraying and cleaning, 

always follow the instructions and 
safety precautions provided by the 
material manufacturer (Refer to 
MSDS).

ElECTrICAl ShOCk hAzArD:

  Follow all local electrical and safety 

codes, as well as the National 
Electrical Code (NEC) and in the 
United States, the Occupational 
Safety and Health Act (OSHA).

  This product requires a grounded 

120V, 15 Amp circuit (See Figure 1). 

MANUAL

NOTE:

  Applies to 120V countries 

only.

  If the power receptacles available 

will not fit this equipment’s power 
cord, then have an appropriate 
power receptacle installed by a 
certified electrician.

  Only qualified electricians or 

service personnel should perform 
maintenance on the electrical 
components of this equipment.

  Do not modify any of the 

electrical components of 
this equipment.

  Do not use a power cord 

adapter with this equipment.

  If using an extension cord, use only 

grounded three wire extension 
cords that are in good condition.

  Check with a qualified electrician 

or service person if the grounding 
instructions are not completely 
understood or you are in doubt 
as to whether the equipment is 
properly grounded.

APPrOPrIATE ExTENSION COrD 

GAUGE FOr GIvEN lENGThS

length of Cord

Gauge

25’

14

25-50’

12

50-100’

10

www.chpower.com

TEST

RESET

Figure 1 - Grounding

Grounding 

Pin

Summary of Contents for PS231B

























Reviews: