background image

ERGOPOWER CONTROL LEVERS - Rev. 00/ 07-2022

CAMPAGNOLO COMPONENTS - TECHNICAL MANUAL

11

• Cut the housing (on the frame side) so that it reaches the 
metal housing stop on the frame (C - Fig. 21). 
• After cutting the housing at the suitable length, fit a 
housing end and insert the housing in the Downtube barrel 
adjuster (C - Fig. 21) on the frame.
• If the frame is the type with internal cable routing, the 
Campagnolo cable tension adjuster for the front derailleur 
included in the package of the Ergopower commands must 
also be installed. Fit the tension adjuster with the knurled 
part at the bottom. The lower housing must provide the 
housing end cap while the upper housing is fitted without 
housing end cap (Fig.22).

The tension adjuster is placed near the handlebar in an area 
where it does not interfere with the frame.

• Ensure that the cable moves fluidly in the housing.

• Pass the cable through the LH slot on the cable guide 
plate (D - Fig. 22) located underneath the bottom bracket 
box and secure the cable to the front derailleur (refer to the 
derailleur technical manual for proper attachment of the 
cable to the front derailleur).

• Refer to the Gearbox and Derailleur Technical Manual (where applicable).

WARNING!

After installation, check that the cables do not interfere with your steering or any other function of your bicycle. Interference could affect your 

ability to turn or control your bicycle, resulting in an accident, personal injury or death.

4.1.3 - ADJUSTING THE CABLE TENSION

C

21

D

22

23

Summary of Contents for Ergopower 13s














Reviews: