Camozzi spa
Società Unipersonale
Via Eritrea, 20/I
25126 Brescia - Italy
Tel. +39 030 37921
Fax +39 030 2400430
www.camozzi.com
Technical assistance
Products inquiries and
requests for support
Tel. +39 030 3792790
Product Certification
Information concerning
product certifications, EC standards,
conformity declarations and instruction
Series TC
Pressure regulator cartridge
Use and maintenance instructions
• Some risks can be related to the product only after its installation on the
machinery/equipment. The end user is responsible for the identification of the
potential safety issue and the reduction of the risks.
• The products described in this manual can be used in circuits which comply with
EN ISO 13849-1 norm
• For information regarding the product reliability please contact Camozzi S.p.A.
• Before using the product, read carefully the information contained in this
document.
• The instructions contained in this manual must be followed together with the
instructions and other information available in:
- Website http://www.camozzi.com
- Camozzi general catalogue
- Camozzi technical support.
• Mounting and operation must be carried out only by qualified and authorized
employees, in accordance with these instructions.
• The machinery/ equipment designer is responsible for choosing the proper
pneumatic component in accordance with its application.
• In case of applications which are not described in this manual or in case of
risks for things, persons or animals, please contact Camozzi S.p.A. before using
the product.
• Do not make any alterations of the product if not authorized, otherwise the user is
responsible for any subsequent damage to things, people or animals.
• All safety rules related to the product must be respected.
• Do not work with the machinery/equipment without having checked that the
working conditions are safe.
• Before the product’s installation or maintenance take care that any lock-out
controls are safely activated. The power supply should then be removed
(if necessary) along with the pressure supply system before exhausting all
residual compressed air in the system. Drain any residual energy stored in
springs, capacitors, reservoirs or vessels. Be aware of any machinery movement
due to gravity when the air is removed from the system.
• The working conditions must be kept between the limitations established
by the technical specifications that can be found under the section “General
Characteristics” of this document and/or in Camozzi general catalogue.
Use the product complying the technical specification contained in the section
• Unless special applications are allowed, do not use the product in environment
where the product might be in direct contact with corrosive gases, chemicals,
salted water, steam or water.
• Avoid, where possible, the installation of devices:
- Where there is direct exposure to sunlight (provide shielding where necessary);
- In proximity of any heat source or in areas subjected to sudden changes in
temperature.
• Before performing any maintenance on the regulator, is to disconnect the
compressed air source allow the release of any residual pressure inside the regulator.
• For this type of product, maintenance or revisions are possible only at a service
center Camozzi S.p.A.
• At the end of the product life cycle, the recyclable-material collection is advisable.
• Comply with the disposal of waste material regulations in force in your country.
The regulator Series TC
regulates and maintains the air
pressure to the desired value,
which can obviously not be
higher than the line pressure.
In order to regulate you need
to turn the regulation screw (
A
),
rotating it clockwise or
anti-clockwise, in any case
the right regulation of the
pressure has to be set upwards
and then block the rotation.
The air flow has to follow the
direction from “
1
” to “
2
”.
Use the nut (
B
) to block the
regulation and avoid accidental
setting changes.
When installing the regulator
cartridge on its sub-base
or in a seat made for a specific
customer application, insert
the O-ring (
C
) and then fix
the regulator cartridge using
screws (
D
), both supplied.
• During the product’s unpacking be careful not to damage it.
• Check that no damages due to transportation or storage are present.
• Do not through away the packaging materials, take care of the disposal and
reconversion of the waste material in compliance with the local regulations.
• Avoid any sudden pressure changes in the circuit where you install the
component.
• The components must be fixed properly, using, where available, the applicable
Camozzi brackets so that the device remains fixed even when the regulator
operates at high frequency or in the presence of strong vibrations.
• Protect the TC pressure regulator from shock danger and from the external action
of mechanical components.
• In the presence of strong vibrations provide special devices / systems that can
reduce the effect on the component.
• When the component has been installed ensure that all pipes are properly
connected.
• Tightening torque of the fastening screw: 0.4 ÷ 0.7 Nm
Made in Italy
93-7522-0099
rev.B
This product is in compliance with the requirements stated in the following standards and/or
technical specifications:
- EN ISO 4414:2010 Pneumatic fluid power
- General rules and safety requirements for systems and their components
Max inlet pressure
10 bar
Range of regulated pressure
0-0,5 / 0-2 / 0-3 / 0-4 bar
Fluid
oxygen, air, inert gas
Ambient temperature
-5 ÷ 50 °C
Mounting
in-line (in any position)
in a dedicated sub-base
in a specific seat (see drawing)
Port size IN (1) / OUT (2)
G 1/8 (only with sub-base)
Exhaust
without relieving
1 General safety instructions
6 Use limitations
7 Maintenance
8 Ecological informations
4 Use
5 Use with sub-base or specific seat
2 General characteristics and use conditions
3 Mounting and installation
Seat for regulator cartridge:
Regulation screw (
A
)
Regulation screw (
A
)
P
OUT
2
P
OUT
2
B
B
D
C
P
IN
1
P
IN
1
