Camon C6 Operating Instructions Manual Download Page 15

CAMON Rotavators

PSR/AM/0912

 

Page 15

Risk Assessment

HAZARDS

RISK LEVEL

ACTION NEEDED

General

The machine should only be used by trained 
operators.

Machine tipping over

Low

Do not use on slopes over 25

o

.

Machine jumping

High

Ensure the centre knife is in good condition 
and adjusted to suit the ground conditions.  
Use the depth adjuster located on top of the 
rotavator to adjust the centre knife

Machine running away

Low

Red stop lever disengages the drive to 
the implement if the operator releases the 
handlebars.  Always check operation before 
use.

Lacerations

Medium

Remove the spark plug cap before carrying 
out any maintenance or cleaning.  Always 
wear gloves when cleaning the tines or 
removing debris.

Machine reversing and jamming 
operator against immovable 
object

High

Never reverse the machine with your back 
to a wall or similar object.

Burns

High

Be very careful or a hot exhaust.  Turn off 
the machine before refuelling.  Allow 1” air 
space in the fuel tank.

Flying objects

Low

Ensure the back flap moves easily and 

follows the contour of the ground to prevent 
small stones being thrown back.  Always 
wear suitable safety footwear.

Handlebar adjustment

Low

Always set the height and sideways position 

before operating the machine - never while 

it is moving.

Foot injuries

Medium

The machine has a safety device to prevent 
the reverse speed and tine drive being 
engaged  simultaneously.  Ensure all safety 
devices are in place before using the machine.  
Always wear suitable safety footwear.

Summary of Contents for C6





















Reviews: