background image

iii 

CE Mark Warning 

This is a Class B product. In a domestic environment, this product may cause radio 
interference, in which case the user may be required to take adequate measures. 

Protection requirements for health and safety – Article 3.1a 

Testing for electric safety according to EN 60950 has been conducted. These are 
considered relevant and sufficient. 

Protection requirements for electromagnetic compatibility  – Article 
3.1b 

Testing for electromagnetic compatibility according to EN 301 489-1, EN 301 489-
17 and EN 55024 has been conducted. These are considered relevant and sufficient. 

Effective use of the radio spectrum – Article 3.2 

Testing for radio test suites according to EN 300 328-2 has been conducted. These 
are considered relevant and sufficient. 

CE in which Countries where the product may be used freely: 

Germany, UK, Italy, Spain, Belgium, Netherlands, Portugal, Greece, Ireland, 
Denmark, Luxembourg, Austria, Finland, Sweden, Norway and Iceland. 
France: except the channel 10 through 13, law prohibits the use of other channels. 

 

                                                                          HW.32 V2.00

 

 

使 用 本 產 品 之 系 統 製 造 商 請 於 設 備 上 標 示 本 產 品 內 含 射 頻 模 組

:

 

 XXXyyyLPDzzzz-x"

  

經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者均不得
擅自變更頻率、加大功率或變更原設計之特性及功能。

  

低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發現有干擾現
象時,應立即停用,並改善至無干擾時方得繼續使用。前項合法通信,指依
電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科
學及醫療用電波輻射性電機設備之干擾。

 

 

 

Summary of Contents for WLG-1801
























Reviews: