Cambridge SoundWorks NEWTON s100 Multipole User Manual Download Page 4

4

POSITIONING YOUR SPEAKERS

The following suggestions assume you have some

flexibility regarding where you place your speakers.

Don’t be too concerned if your situation and listening

environment dictate the speakers’ position. As long 

as each surround speaker is on the left or right half 

of the listening space, the speakers are will provide

convincing, lifelike sound.

Mounting:

The typical way to position surround speak-

ers is to wall-mount them on a protruding screwhead.

Other methods are to place them on short shelves, to

mount them on short swivel brackets, or to install them

on floor stands.

Notice:

The speakers are marked LEFT and RIGHT.

Most often, the speakers will be wall-mounted with the

MultiPole switch panel facing down. In this case,

mount the LEFT speaker on the listener’s left side and

the RIGHT speaker on the listener’s right side (see 

diagram A).

You may need to invert the speakers to provide 

access to the MultiPole switch (such as when placing

them on small support shelves or floor stands). In this

case, reverse the speakers’ left/right positions (see 

diagram B).

Front to Back placement: Place each surround speak-

er to the left or right of the listening area. Try to 

position the speakers within two feet of a line centered

on your listening postion (see diagram C).

Height: Place each speaker at least four feet above

the floor, up to seven feet above the floor (see 

diagram D).

Note:

It is not critical that the left and right speakers

be the same distance from the front speakers or 

equal heights.  

If you don’t have walls on both sides of your listening

area, try to avoid placing both surround speakers on 

a wall behind the listening postion. Sonically, it’s still

better to place one speaker on a side wall and one

speaker on a rear wall. This provides better separation

than two speakers on a wall behind the listeners.

S100

LEFT

8 Ohms

Made In China

WALL MOUNTED - SWITCH FACING DOWNWARD

RIGHT SPEAKER

LEFT SPEAKER

7 Ft.

4 Ft.

Back of Speaker

Front to Back Placement 

of Surround Speakers

Stand Mounted 

Switch Facing Upward

Wall Mounted Height Placement

A.

B.

C.

D.

SPEAKERS ARE LABELED “LEFT” OR “RIGHT”

2 FEET

2 FEET

CENTER LINE OF LISTENING POSITION

Summary of Contents for NEWTON s100 Multipole













Reviews: