background image

 -

  Placement of the speakers affects how well the AV surround system 

recreates the sound field intended by the recording engineer. Current 

recording practice typically assumes a speaker array with a center channel 

speaker directly in front of the central viewing position, and with left and right 

speakers placed so they each form a 30 degree angle from the center line. 

Left and right surround speakers are placed 110 degrees from the center line. 

Left and right rear speakers in a 7.1 system are typically at 140 degrees. If 

a single rear speaker is used in a 6.1 system, it should be centered on the 

rear wall. Front speakers should be as close to the height of the TV monitor 

as practical. Surround and rear speakers should be slightly higher. The best 

recreation of the desired sound field is achieved by recreating this speaker 

pattern as closely as your room and furnishings allow. 

   Don’t be too concerned if your situation and listening environment dictate 

somewhat different speaker positions. Most rooms do not allow ideal 

placement. Place your speakers as close to these guidelines as practical and 

the speakers will still provide convincing, lifelike sound.

   Your surround processor has a variety of adjustments to optimize the sound 

based on the speakers’ capabilities and placement. These adjustments vary 

by processor, so refer to your processor’s manual for instructions specific to 

your equipment. Set your main, center, and surround settings to “SMALL”, 

with subwoofer “ON”.  

• Avoid placing front left and right speakers very close to a side wall (within 

12-14 inches). The reflected sound from the wall degrades the sound coming 

directly from the speaker.

Speaker Placement

SURROUND

SPEAKER

SURROUND

SPEAKER

POWERED

SUBWOOFER

MAIN SPEAKERS

LEVEL

WITH

CENTER

SPEAKER

140º

140º

110º

110º

30º

30º

7.1 REAR

SPEAKER

7.1 REAR

SPEAKER

MAIN

SPEAKER

MAIN

SPEAKER

RECOMMENDED HOME 

THEATER SETUP

CENTER   CHANNEL

Summary of Contents for MC630-IW















Reviews: