AX
R85
AX
R100
ENGLISH
8
BLUETOOTH ANTENNA
Used for wireless streaming bluetooth (A2DP/AVRCP) audio capability directly from
most phones, tablests and laptops. See later section for details.
9
LOUDSPEAKER TERMINALS
Two sets of loudspeaker terminals are available, A (main loudspeaker terminals, top row)
and B (secondary switchable loudspeaker terminals, bottom row). Connect the wires
from your left channel loudspeaker to the Left positive and negative terminals, and the
wires from the right channel loudspeaker to the Right positive and negative terminals.
In each case, the red terminal is the positive output and the black terminal is the
negative output.
Care should be taken to ensure no stray strands of wire are shorting speaker
outputs together. Please ensure that the loudspeaker terminals have been tightened
adequately to provide a good electrical connection. It is possible for the sound quality
to be affected if the screw terminals are loose.
The use of A and B speakers affords you an easy and inexpensive way to create a
simple multi-room system.
Note: When using two pairs of speakers, use speakers with a nominal impedance
of
16
ohms.
10
HEAT TUNNEL VENT GRILLE
Allows cooling of internal circuitry via the heat tunnel. DO NOT OBSTRUCT!
11
VOLTAGE SELECT SWITCH
For servicing use only.
12
AC POWER SOCKET
Once all connections are complete, plug the AC power cable into an appropriate
mains socket and turn the unit on.
Ground
Ground
Left
Right
A
B
A
B
Left
Right
Max Power Consumption: 550W
Mains Voltage Selector Switch
115/220-230V~ 50/60Hz
Power AC
A1
D1
D2
D3
A2
A3
Rec Out
Sub Out
Rec Out
Sub Out
A3
A1
D1
D2
D3
MM
Phono
MM
Phono
A2
Designed & Engineered in Great Britain
Assembled in China
AXR100
Stereo Receiver
Loudspeaker Terminals
Impedance 4–8 ohms
5V 400mA
Service Port
AM 300
Ω
FM 75
Ω
Designed & Engineered in Great Britain
Assembled in China
Max Power Consumption: 500W
Mains Voltage Selector Switch
115V/220-230V AC~50/60Hz
Power AC
Ground /
Ground
Left
Right
A
B
A
B
Left
Right
AM 300
Ω
FM 75
Ω
Service Port
5V 400mA
A1
A2
A3
Rec Out
Sub Out
Rec Out
Sub Out
A3
A1
MM
Phono
MM
Phono
AXR85
Stereo Receiver
A2
Loudspeaker Terminals
Impedance 4–8 ohms
Rear panel connections
1
DIGITAL INPUTS
(AXR100 ONLY)
Toslink and S/P DIF co-axial digital inputs.
Note:
To obtain the best results from your system we recommend using only high
quality Cambridge Audio interconnects. This will ensure that you hear your system
as we designed it. Please ask you dealer for details.
2
AUDIO INPUTS
These inputs are suitable for any ‘line level’ source equipment such as the audio
outputs of CD players, BD/DVD players, etc.
3
PHONO INPUT
This input has a built in phono stage. Record players fitted with Phono Cartridges
of the Moving Magnet (MM) or high output Moving Coil (MC) type (between 2-6mV
output and 30-50k load impedance) can be used. Low output Moving Coil types
(<1mV and usually 10-1000 ohm load impedance) cannot be directly connected
and will require a matching transformer or head amp. Please consult your dealer
for details. The ‘ground’ terminals on both the record player and the
AXR
should be
connected (where possible) with a ground wire for lowest noise/hum pickup.
4
REC OUT
Connect to the recording input of a tape deck, CD recorder input, etc.
5
SUB-OUT
For optional connection to the input socket of an active subwoofer if desired.
6
AM/FM ANTENNA
Tuner aerial connections for picking up radio signals. Refer to the ‘Connections’
section of this manual. For permanent use, outdoor AM/FM aerials are highly
recommended.
7
SERVICE PORT
For servicing use only. Do not connect anything here as it may result in damage.
2
1
7
3
4
9
10
6
12
11
5
8
