Cambium Networks PTP 820C Installation Manual Download | Manualshive

Page: 32 / 206

background image

Chapter 2: Product Hardware Description

System Components

phn-3962 004v000

Page 2-8

System Components

The following figures show the main components used in the PTP 820C installation procedures.

Note

The availability of the installation components follows the PTP 820C frequency rollout
as stated in the published roadmap.
The presence of a specific component in this manual does not indicate that it is
available for ordering. Please consult with your respective pre-sales engineer for
specific component availability.

Figure 8 System Components

PTP 820C

Dual Core Coupler/Splitter

DC OMT

DC Splitter

Adaptor for 6 GHz - 13 GHz

PoE Injector

Dual Core Mediation Device

Remote Pole Mount

Remote Dual Pole Mount

«
...
30
31
32
33
34
...
»

Summary of Contents for PTP 820C















































































































































































































Reviews:

No comments

Related manuals for PTP 820C

Twin Coil Ferrite

Brand: C. Crane Pages: 16

Brand: CSL Pages: 8

AVANT CPE 150Mbps

Brand: Smart Lan Pages: 11

Amplified Receive-Only Magnetic Loop Antenna

Brand: W6LVP Pages: 2

Brand: Duratrax Pages: 2

Brand: Gotting Pages: 60

Brand: soundsation Pages: 20

Brand: Radio Shack Pages: 2

Brand: Yaesu Pages: 1

Brand: MotoSAT Pages: 2

Brand: SELFSAT Pages: 61

Brand: WADE Antenna, Inc. Pages: 2

Brand: THOMSON Pages: 38

Brand: Televes Pages: 4

Brand: Oyster Pages: 160

Brand: Leica Pages: 41

Brand: Pason Pages: 26

Brand: Mohu Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands