background image

Chapter 1:  Before You Start 

PTP 820 Assured Platform 

 

phn-3962 004v000 

Page 1-7 

PTP 820 Assured Platform 

PTP 820 Assured platform enhances network reliability and security, ensuring that mission-critical 

networks maintain availability, and protecting the confidentiality and integrity of their users’ data.

 

The PTP 820 Assured platform is compliant with FIPS 140-2, including: 

 

Compliance with FIPS 140-2 specifications for cryptography module. 

 

FIPS 140-2 Level 2 physical security. 

 

AES-256 encryption (FIPS 197) over radio links. 

The PTP 820 Assured platform also provides: 

 

Secured communication and protocols for management interface. 

 

Centralized user authentication management via RADIUS. 

 

Advanced identity management and password policy enforcement. 

 

Security events log. 

 

Secure product architecture and development. 

The following products are included in the PTP 820 Assured platform: 

 

PTP 820C Assured 

 

PTP 820S Assured 

 

PTP 820G Assured 

 

 

Note 

PTP 820 Assured is supported with certain versions of the release. To determine 
whether a specific release version supports PTP 820 Assured, check the Release 
Notes for the current system release. 

 

 

Summary of Contents for PTP 820C















































































































































































































Reviews: