Cambium Networks PTP 820 Series Installation Manual Download Page 27

Page: 27 / 179

Installation Guide for RFU-D-HP

Page 27 of 179

Antenna Connection

RFU-D-HP can be mounted directly for 6 to 11 GHz using the following antenna types (for integrated antennas, specific
antennas are required):

•

CommScope: VHLP series

•

Radiowave: HP Series

For remote mount installations, the following Flexible Waveguide flanges should be used (millimetric). The same
antenna type (integrated) as indicated above can be used (recommended).

Other antenna types using the flanges listed in the table below may also be used.

Table 3: Antenna Flanges

Frequency Band Range (GHz)

Rect. WG Flange Des. Radio Side (Remote) Flange Des.

6(L/U) GHz

5.8-7.1

WR137

UDR70

7/8 GHz

7.1-8.5

WR112

UBR84

10/11 GHz

10.0-11.7

WR90

UBR100

If a different antenna type (CPR flange) is used, a flange adaptor is required. Please contact your Cambium Networks
representative for details.

Note!

Appropriate lubricant or grease can be applied to the screws that connect the RFU-D-HP to the
antenna interface.

There is no direct WG connection. An adaptor is required to connect the RFU to the WG.

Summary of Contents for PTP 820 Series




















































































































































































Search results

Summary of Contents for PTP 820 Series

Reviews:

Brands by name

Popular brands

Cambium Networks PTP 820 Series, Installation Manual

Search results

Summary of Contents for PTP 820 Series

Reviews:

Brands by name

Popular brands