Cambium Networks cnPilot Home R200 Series User Manual Download Page 13

Page: 13 / 136

List of Tables

pmp-0884 (September)

xiii

About This User Guide

Thank you for choosing Cambium cnPilot Home & Small Business WiFi router with ATA and optional PoE

support.

This manual provides basic information about how to install and deploy the cnPilot Home R200x or the R201x

WiFi routers with VoIP to the Internet.

For remote configuration and deployment, an IP connection is required.

The cnPilot Home & Small Business router with VoIP is a managed device (that yet has the ability to act as a

stand-alone router if desired). In addition to WiFi, this product provides high quality voice calls as well as the
optional ability to power Cambium’s ePMP series subscriber module or the PMP450 series subscriber module by
supporting Cambium’s

(Canopy) PoE. For voice calls, the product is fully compatible

with the SIP industry standard and is able to interoperate
with many other SIP devices and software on the market.

Summary of Contents for cnPilot Home R200 Series









































































































































Search results

Summary of Contents for cnPilot Home R200 Series

Reviews:

Related manuals for cnPilot Home R200 Series

Brands by name

Popular brands

Cambium Networks cnPilot Home R200 Series, User Manual

Search results

Summary of Contents for cnPilot Home R200 Series

Reviews:

Related manuals for cnPilot Home R200 Series

Brands by name

Popular brands