background image

June 2020

TO OBTAIN WARRANTY SERVICE  

PLEASE CALL 1-309-629-9000

P.O. Box 9  |  Alpha, IL  61413  |  (309) 629-9000  | fax (309) 629-9001

www.CalmerCornHeads.com

The replacement parts comprising and the methods associated with Calmer’s Residue Man-

agement Program are covered by the following patents issued by the United States Patent 

and Trademark Office: 7,886,510, 8,171,708, 8,220,237, 8,464,505, 8,857,139, 8,863,487, 

9,554,511, 9,560,804, 9,668,414, 10,039,232, 10,045,483

Calmer Corn Heads Residue Management Upgrade Kit Limited Warranty

Calmer warrants our parts 100%.  This warranty is good throughout the first season after purchase of the part.  

What this means is that if the part breaks within the first season of use, we will replace the part with a new one without 

charge to you.  Calmer pays for the shipping both ways as well.  In the alternative, if you wish, we will refund to you all of 

the money you paid to Calmer for the part. If the Calmer part does not work in a manner that you expected, we prom-

ise that we will work with you to adjust settings and to see if we can obtain satisfactory performance.   In the end, if the 

Calmer part does not work on your farm to your complete satisfaction, we will refund your purchase price.  Disclaimers:  

Calmer is not responsible for and does not warrant as to consequential damages or any other types of damages that may 

be claimed as a result of part breakage or unsatisfactory performance.   In other words,  except as stated herein all other 

warranties or liabilities, expressed or implied, oral or statutory, including any warranty of merchantability or fitness for a 

particular purpose are expressly denied.  

“The information in this book reflects some of the data 

I’ve collected throughout my 30+ years of conducting 

on-farm research. I hope you found it useful and are 

encouraged enough to do your own on-farm research. 

After all, we can’t improve what we don’t measure!”

M A R I O N   C A L M E R

CEO – Calmer Corn Heads, Inc. 

President – Calmer’s Independent Ag Research Center  

Owner/Operator – Calmer Farms

Summary of Contents for BT Chopper Upgrade Kit





















Reviews: