Lift Knob
Hole Rod
Strap
Nut
Ball
Rod
Cone
Washers
Fiber
Washers
Drain
Tailpiece
Rubber
Washer
Drain
Collar
Stopper
Drain
Rim
Adjustable
Eye-Screw
Nut
NOTE:
Hot & cold valves are labeled:
cold=blue & hot=red
.
-Remove top nut and turn bottom nut with fiber washer down
the valve until it stops.
-Insert valve through hole from below and install top nut
(if applicable), and adjust to proper height, see Fig. 4A
(also refer to "A" dimension table on page 1).
-Tighten the bottom nut to secure the valve.
-Install trim parts (base ring if applicable), escutcheon and handle
and tighten handle set screws with Allen key provided.
REMINDER: Please retain allen key as handles may
require re-tightening with normal use.
-Attach flex lines to valve and spout tee. Hand-tighten. Then go
1/4 to 1/2 turn more with wrench (not supplied). Do not overtighten.
Brass
Nut
Connect faucet to water supply:
IMPORTANT:
Flush supply lines of all debris prior to connecting to lavatory
valve bodies. Debris remaining in the line will damage valve bodies and
cause leaking. Failure to flush the lines could result in voiding the warranty.
5
Install "P" trap:
-Connect your waste "P" trap
to the drain tailpiece.
Fig. 4A
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Adjustable
Eye-Screw
Ball
Rod
Lift
Rod
Drain
Tailpiece
"P" Trap
(not supplied)
Angle Stop
(not supplied)
Valve
Body
Supply Riser
(not supplied)
2
Install valve bodies:
Spring
Clip
Lock
Nut
-Connect supply risers from the angle stops.
NOTE:
P-trap, angle stops, and supply risers
are not supplied. We recommend genuine
Cal-Trim parts available at your authorized
California Faucets dealer.
Installation Note for series:
# 32, 33, 34, 35, 36, 43, 57, 60, 61, 65, 66, 67, 68 & 69.
The trim to those products do not require a top nut to be installed
on the valve (See Fig. 4A)
The decorative base ring and escutcheon takes the place of the
top nut. (See Fig. 4B).
Fig. 4B
Top
Nut
Fiber Washer
Bottom Nut
Valve Body
Flex Line
Brass Nut
(Supplied)
"A"
Sink/
Countertop
Decorative
Base Ring
Valve
Pg 2
4
3
Install pop-up assembly.
-Separate drain collar from pop-up assembly.
-Apply silicon caulking to underside of drain collar.
NOTE: Do not use
"Plumbers Putty" or any oil based sealants! Use of anything other than
silicon caulking will VOID the finish warranty.
-Insert drain body from underside through sink. Slowly screw on drain
collar, align with ball rod hole facing back wall, then gently pull down into
sink and firmly tighten brass nut from below.
-Remove tailpiece from drain body and apply teflon tape, approx. 3 to
5 wraps around threads and reinstall into bottom of drain body.
-Insert stopper in collar and hold with eye-screw hole facing back.
If necessary, adjust stopper eye-screw height by loosening lock nut and
rotating counter-clockwise. Tighten lock nut
(See Fig. 6)
.
-Remove spring clip from ball rod.
-Remove nut and cone washers and slide onto end of ball rod.
-Insert ball rod into drain body below so short end of ball rod end fits
in stopper eye-screw hole. Snug ball rod nut (do not over tighten).
Ball rod must move up & down freely
(See Fig. 6)
.
-Insert lift rod through top of spout and then through hole rod strap
underneath sink. Tighten thumb-screw of hole rod strap
against lift rod and connect to ball rod by gently pinching locking
spring clip and sliding one side of spring clip onto ball rod.
-Insert hole strap onto ball rod, then pinch spring clip together to fit
on ball rod.
WS_ii_120917
