background image

Page 9

SECTION III: PRE-INSTALLATION

LOCATION

CAUTION 

This water heater must be located in an area where leakage of the tank, water line

connections, or the temperature and pressure relief valve will not result in damage to

the area adjacent to the water heater or to lower floors of the structure.  When such

location cannot be avoided, a suitable drain pan must be installed under the water

heater.  The drain pan depth must be suitable for draining and collecting water.  The

drain pan can be purchased from your plumbing professional.  The drain pan must be

piped to an adequate drain and all drain piping must be at least 0.75” in diameter

and pitched for proper drainage.

CAUTION 

DO NOT store or use gasoline or other flammable, combustible, or corrosive vapors

and/or liquids in the vicinity of the water heater or any other appliance.

IF YOU SMELL GAS:

• DO NOT try to light any appliance.

• DO NOT touch any electric switch; do not use any telephone in your building.

• Immediately call your gas supplier from a telephone in another building.  Follow your

gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire department.

DO NOT OPERATE THE APPLIANCE UNTIL THE LEAKAGE IS CORRECTED!

CAUTION 

Do not drop water heater or lay heater down on its side.  Move the water heater into

position by sliding or using an appropriately sized hand truck.

The solar indirect water heater must be installed indoors.  Locate the water heater as close as
practical to the solar heating system and leave sufficient clearances for servicing the heater.
The entire solar heating system should be located as close as possible to points of hot water
use for the fastest delivery of hot water.  This water heater may be installed on combustible
flooring.  DO NOT install this water heater on carpeting.

See Tables 4 and 5 for combustible and service clearances.

!

!

!

Top

Sides

Front

Rear

0

´´

0

´´

0

´´

0

´´

Top

Sides (non-piping) Side (T&P Relief Valve)

Front

Rear

12

´´

4

´´

6

´´

16

´´

0

´´

Table 4: 

Clearance from Combustible Materials

Table 5: 

Recommended Service Clearances

Summary of Contents for NAS20053

























Reviews: