Caldera Highland Series, Owner'S Manual

Page: 14 / 32

11
OPERATING INSTRUCTIONS
MYSTIQUE
®
LED LIGHTING (OPTIONAL)
The Mystique LED lighting system allows you to brighten up your spa experience through different multi-colored lights: blue, aqua, green, amber, red, and magenta. You
can choose one stationary color or you can cycle through all the colors with the automatic color wheel.
To install Mystique LED lighting system, you will need to contact your Caldera Dealer.
To activate, press the “SET” button, then the “LIGHT” button on the control panel. The LIGHT icon will flash once color wheel is active. To select a specific color, push
the “LIGHT” button (within 5 seconds) while the desired color is displayed. If 5 seconds have passed after color wheel activation, you will need to press “SET”, then
“LIGHT” to select a specfic color. The Mystique LED lighting option is a great way to personalize your spa experience.
LOCK FEATURES
The locking features, TEMPERATURE LOCK and SPA LOCK, are enabled from the control panel by a specific combination of buttons. Once enabled, a lock will remain
active until the specific button combination is applied to disable the lock. Even if power is disconnected from the spa and soon thereafter reapplied (such as a power
outage), the lock will remain in place.
SPA LOCK
The Spa Lock feature deactivates all of the functions of the control panel. It is generally used to prevent unwanted use of the spa.
To activate the Spa Lock, press “SET” button then “TEMP
▼
” button. The word “ SLOC ” in the display will confirm activation.
To deactivate the Spa Lock, press “SET” button then “TEMP
▼
” button. At this point, the “ SLOC ” will no longer be illuminated in the display.
TEMPERATURE LOCK
The Temperature Lock feature deactivates the temperature control function from the control panel. All other functions on the control panel will operate normally.
Temperature Lock is most often used by those who do not want others to change the set temperature of the spa water.
To activate the Temperature Lock, press “SET” button then “TEMP
▲
“ button. The word “ TLOC ” in the display will confirm activation.
To deactivate the Temperature Lock, press “SET” button then “TEMP
▲
“ button. At this point, the “ TLOC ” will no longer be illuminated in the display.
FILTER CYCLES
Your spa will automatically turn the filter cycle on twice each day. When the spa is first powered up the automatic filter cycle will wait 10 minutes before
starting. A 1.5 hour filter cycle using the low speed of the jet pump is the programmed default filter cycle time. The display will read 1:30. The filter
cycle occurs twice a day (every 12 hours).
NOTE: The optional Monarch
®
and PureWater TM ozone systems only work during the filter cycles.
To modify the length of either filter cycle:
A. Press and hold the “SET” button for approximately three seconds (The filtration ion will flash during programming).
B. Press the “LIGHT” button to select the Filter Cycle 1 or 2 (a F1 or F2 will flash in the display). NOTE: Each filter cycle can be set independently.
C. Using the TEMP
▲
or the TEMP
▼
button, adjust the length of filtering time desired (0 to 6 hours).
D. Programing will then be saved 10 seconds after the last button is pushed.
The filter cycle will activate the low speed of the jet pump for the entire cycle. When activated, the filter cycle icon on the display is turned on. If the temperature
exceeds the set point by three degrees F for more than three hours, the system will cancel the FILTER cycle and the filter cycle icon will blink for the remaining filter
cycle time. Should the temperature cool down to 1.5 degrees F within the set point before the end of the cycle, the cycle will resume for the rest of the time. Should you
use the spa during the filter cycle by placing the jet pump on high speed, the filter cycle icon will blink. Once the jet pump has been shut off, a ten minute tranquil mode
begins (filter cycle icon will be blinking during tranquil mode) before the filter cycle will resume. The blinking filter cycle icon indicates that the filter cycle timer is still
counting, but the cycle has been temporarily interrupted.
NOTE : The interrupted time of a filter cycle is not extended after the filter cycle resumes. Power interruptions of the spa will reset the filter cycle to the default 1.5 hour
cycle time and begin 10 minutes after spa regains power.
OPERATION NOTE: For proper water-circulation during filtration cycles, rotate the air control valves counterclockwise to the off position.
MANUAL CLEAN CYCLE
The clean-up cycle operates in the following manner: Jet pump 1 runs for ten minutes on high speed.
This system is initiated by pressing the “SET” button, then “JETS” button. The Filter and Jets icon will flash.