CalAmp 4530HE Hardware And Installation Manual Download | Manualshive

Page: 11 / 43

background image

Sleep

LMU

Processor

STM32F205

App ID

321-HSPAg6

3.4.1 3-Axis Accelerometer Input

The LMU-4530™ supports an internal 3 Axis Precision Accelerometer as one of its discreet inputs.

When the LMU is moved in any direction, the associated input will be in the High state. If the LMU’s

accelerometer does not detect motion, then the input will be in the Low state. No external connections

are required for this functionality to be operational.

3.4.2 Status LEDs

The LMU-4530™ is equipped with three Status LEDs, one for GPS, one for COMM (wireless network

status) and one TBD. The LEDs use the following blink patterns to indicate service:

LED #1 (Comm LED - Orange) Definitions

Condition

LED 1

Modem Off

Off

Comm On - Searching

Slow Blinking

Network Available

Fast Blinking

Registered but no Inbound Acknowledgement

Alternates from Solid to Fast Blink every 1s

Registered and Received Inbound Acknowledgement

Solid

LED #2 (GPS LED - Yellow) Definitions

«
...
9
10
11
12
13
...
»

Summary of Contents for 4530HE












































Reviews:

No comments

Related manuals for 4530HE

Brand: Garmin Pages: 16

Brand: optitrack Pages: 2

Brand: Unireach Pages: 6

Vertex Plus Survey

Brand: Vectronic Aerospace Pages: 24

Brand: Holux Pages: 14

Brand: Queclink Pages: 8

RoadMate 9200-LM

Brand: Magellan Pages: 45

Brand: Sensitech Pages: 2

Brand: Lkgps Pages: 6

Brand: Navico Pages: 236

BIG 5 GPS METER

Brand: Hobbico Pages: 4

FindnSecure FS-65

Brand: EMBARC Pages: 52

Brand: Trafficmaster Pages: 2

Brand: AmbiCom Pages: 24

Brand: Lowrance Pages: 208

Brand: Raymarine Pages: 58

Brand: Xexun Pages: 13

Brand: Xexun Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands