background image

31-2000694 Rev. 1

9

Installation Instructions

3   DOOR REMOVAL

NOTE: 

Door removal is not a requirement 

for installation of the product but is an added 
convenience.

To remove the door:

A. Open the oven door as far as it will go.

B. Remove hinge bracket, if equipped, 

from front frame and set aside. 
The hinge bracket must be 
replaced, if equipped, for proper 
door functionality when door is 
reinstalled.

C. Push both hinge locks down toward 

the door frame to the unlocked 
position. This may require a flat-
blade screwdriver. 

DO 

NOT LIFT THE DOOR BY 
THE HANDLE!

D. Place hands on 

both sides of the door 
and close the oven 
door to the removal 
position (approximately 1”–2” [2.5 cm–5.1 cm] from 
the closed position).

E. Lift the door up and out until the hinge arms clear 

the slots. 

NOTE: 

The oven door is very heavy. Be 

sure you have a firm grip before lifting the oven 
door off the hinges. Use caution once the door is 
removed. Do not lay the door on its handle. This 
could cause dents or scratches.

Hinge Bracket

Hinge Slot

Hinge Arm

Hinge Unlocked 
Position

Hinge Clears Slot

4   ELECTRICAL REQUIREMENTS

WARNING

 This appliance must be properly 

grounded.

WARNING

 To prevent fire or shock, do not use 

an extension cord with this appliance.

WARNING

 To prevent shock, remove house 

fuse or open circuit breaker before beginning 
installation.

WARNING

 Improper connection of aluminum 

house wiring to copper leads can result in an 
electrical hazard or fire. Use only connectors designed 
for joining copper to aluminum and follow the 
manufacturer’s recommended procedure closely.

We recommend you have the electrical wiring and 
hookup of your appliance connected by a qualified 
electrician. After installation, have the electrician show 
you how to disconnect power from the appliance.

You must use a single-phase, 120/208 VAC or 
120/240 VAC, 60 Hertz electrical system. If you 
connect to aluminum wiring, properly installed 
connectors approved for use with aluminum wiring 
must be used.

Effective January 1, 1996, the National Electrical 
Code requires that new construction (not existing) 
utilize a four-conductor connection to an electric oven. 
When installing an electric oven in new construction, 
a mobile home, recreational vehicle or an area where 
local codes prohibit grounding through the neutral 
conductor, refer to the section on four-conductor 
branch circuit connections.

Check with your local utilities for electrical codes which 
apply in your area. Failure to wire your oven according 
to governing codes could result in a hazardous 
condition. If there are no local codes, your oven must 
be wired and fused to meet the National Electrical 
Code, NFPA No. 70 – latest edition, available from the 
National Fire Protection Association.

Summary of Contents for CMB903M





























Reviews: