Cadillac Escalade 2020 Owner'S Manual Download Page 94 | Manualshive

Page: 94 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

94

SEATS AND RESTRAINTS

5. To tighten the belt, push down

on the child restraint, pull the
shoulder portion of the belt to
tighten the lap portion of the
belt and feed the shoulder belt
back into the retractor. When
installing a forward-facing child
restraint, it may be helpful to use
your knee to push down on the
child restraint as you tighten
the belt.

Try to pull the belt out of the
retractor to make sure the
retractor is locked. If the
retractor is not locked, repeat
Steps 4 and 5.

6. If the child restraint has a top

tether, follow the child restraint
manufacturer

’

s instructions

regarding the use of the top
tether. Refer to the instructions
that came with the child
restraint and see

Lower Anchors

and Tethers for Children (LATCH
System)

.

7. Before placing a child in the

child restraint, make sure it is
securely held in place. To check,
grasp the child restraint at the
seat belt path and attempt to
move it side to side and back
and forth. When the child
restraint is properly installed,
there should be no more than
2.5 cm (1 in) of movement.

To remove the child restraint,
unbuckle the vehicle seat belt and let
it return to the stowed position. If the
top tether is attached to a top tether
anchor, disconnect it.

If the head restraint was removed for
a third row outboard seating position,
reinstall it before the seating position
is used. See

“

Head Restraint Removal

and Reinstallation

”

under

Anchors and Tethers for Children
(LATCH System)

for additional

information on reinstalling the head
restraint properly.

Securing Child Restraints
(With the Seat Belt in the
Front Seat)

This vehicle has airbags. A rear seat is
a safer place to secure a
forward-facing child restraint. See

Where to Put the Restraint

In addition, the vehicle has a
passenger sensing system which is
designed to turn off the front
outboard passenger frontal airbag
under certain conditions. See

Passenger Sensing System

and

Passenger Airbag Status Indicator

for more information, including
important safety information.

Never put a rear-facing child seat in
the front. This is because the risk to
the rear-facing child is so great if the
airbag deploys.

«
...
92
93
94
95
96
...
»

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Brand: Ultra-tow Pages: 14

Brand: Mercedes-Benz Pages: 121

Brand: Menabo Pages: 8

Brand: Camtree Pages: 5

Brand: Ford Pages: 2

Brand: AutoWatch Pages: 4

Brand: Honda Pages: 85

Brand: TAUBENREUTHER Pages: 8

StreetLine Series

Brand: SAAS Pages: 4

Truck Training Model

Brand: WABCO Pages: 56

OCTAVIA - TECHNICAL CHANGES 11-2009

Brand: Skoda Pages: 16

Brand: ULTIMATE SPEED Pages: 32

Brand: Chevrolet Pages: 441

Brand: Navman Pages: 10

Brand: Macrom Pages: 10

Brand: Honda Pages: 268

Brand: Metra Electronics Pages: 20

3 Facelift 2006

Brand: Mazda Pages: 94

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands