manualshive.com logo in svg

Cadillac Escalade 2020, Owner'S Manual

The Cadillac Escalade 2020 Owner's Manual is now available for download, absolutely free! This comprehensive manual is a must-have for every Escalade owner, providing essential information and guidance. Visit manualshive.com now to access and download your manual instantly, ensuring a seamless ownership experience.

Share
Download
background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

VEHICLE CARE

323

Caution

Lubrication of applicable steering/
suspension points should not be
done unless the temperature is

−

12 °C (10 °F) or higher, or damage

could result.

Body Component Lubrication

Lubricate all key lock cylinders, hood
hinges, liftgate hinges, steel fuel door
hinge and power assist step hinges,
unless the components are plastic.
Applying silicone grease on
weatherstrips with a clean cloth will
make them last longer, seal better,
and not stick or squeak.

Underbody Maintenance

At least twice a year, spring and fall,
use plain water to flush any corrosive
materials from the underbody. Take
care to thoroughly clean any areas
where mud and other debris can
collect. If equipped with power assist
steps, extend them and then use a
high pressure wash to clean all joints
and gaps.

Do not directly power wash the
transfer case and/or front/rear axle
output seals. High pressure water can
overcome the seals and contaminate
the fluid. Contaminated fluid will
decrease the life of the transfer case
and/or axles and should be replaced.

Sheet Metal Damage

If the vehicle is damaged and requires
sheet metal repair or replacement,
make sure the body repair shop
applies anti-corrosion material to
parts repaired or replaced to restore
corrosion protection.

Original manufacturer replacement
parts will provide the corrosion
protection while maintaining the
vehicle warranty.

Finish Damage

Quickly repair minor chips and
scratches with touch-up materials
available from your dealer to avoid
corrosion. Larger areas of finish
damage can be corrected in your
dealer's body and paint shop.

Chemical Paint Spotting

Airborne pollutants can fall upon and
attack painted vehicle surfaces
causing blotchy, ring-shaped
discolorations, and small, irregular
dark spots etched into the paint
surface. See

“

Finish Care

”

previously in

this section.

Interior Care

To prevent dirt particle abrasions,
regularly clean the vehicle's interior.
Immediately remove any soils.
Newspapers or dark garments can
transfer color to the vehicle

’

s interior.

Use a soft bristle brush to remove
dust from knobs and crevices on the
instrument cluster. Using a mild soap
solution, immediately remove hand
lotions, sunscreen, and insect
repellent from all interior surfaces or
permanent damage may result.

Use cleaners specifically designed for
the surfaces being cleaned to prevent
permanent damage. Apply all cleaners
directly to the cleaning cloth. Do not
spray cleaners on any switches or
controls. Remove cleaners quickly.

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Camcar 40052 Mounting Instructions preview
40052
Brand: Camcar Pages: 6
ABL eMH1 WALLBOX Manual preview
eMH1 WALLBOX
Brand: ABL Pages: 176
ABL eMH1 WALLBOX Installation Manual preview
eMH1 WALLBOX
Brand: ABL Pages: 94
Ecco Gemineye EC2014-C Installation Instructions Manual preview
Gemineye EC2014-C
Brand: Ecco Pages: 10
Ecco Reflex 5500 Series Installation And Operating Instructions Manual preview
Reflex 5500 Series
Brand: Ecco Pages: 12
TATA Motors Safari Owner'S Manual & Service Book preview
Safari
Brand: TATA Motors Pages: 161
TAUBENREUTHER 16 - 590 Fitting Instructions Manual preview
16 - 590
Brand: TAUBENREUTHER Pages: 11
Yakima SKYBOX Series Manual preview
SKYBOX Series
Brand: Yakima Pages: 15
Uniden BTSC1500 Owner'S Manual preview
BTSC1500
Brand: Uniden Pages: 16
Uniden BTSC1500 User Manual preview
BTSC1500
Brand: Uniden Pages: 20
Federal Signal Corporation CommCenter D1 Series Installation And Service Instructions Manual preview
CommCenter D1 Series
Brand: Federal Signal Corporation Pages: 16
FormFit HD 23A 07 Installation Instructions preview
HD 23A 07
Brand: FormFit Pages: 4
Air Lift WirelessAIR 73000EZ Manual preview
WirelessAIR 73000EZ
Brand: Air Lift Pages: 12
Quadratec QuadraTop 11051.0415 Installation Manual preview
QuadraTop 11051.0415
Brand: Quadratec Pages: 8
Packard 1948 eight Operating Instructions Manual preview
1948 eight
Brand: Packard Pages: 25
Ford Escape 2022 Owner'S Manual preview
Escape 2022
Brand: Ford Pages: 585
Brink 5978 Fitting Instructions Manual preview
5978
Brand: Brink Pages: 21
FVC Sprinter Bed System DIY Installation Manual preview
Sprinter Bed System DIY
Brand: FVC Pages: 8

Brands by name

Popular brands

Load more brands