Cadillac Escalade 2020 Owner'S Manual Download Page 17 | Manualshive

Page: 17 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

KEYS, DOORS, AND WINDOWS

17

2. Position the bottom edge of the

cap under the lower edge of the
metal piece (6). The tabs (7)
attach to metal piece (6) at the
positions (5).

3. Rotate the cap upward to install

into place.

4. Check that the cap is secure.

5. Release the door handle.

Free-Turning Locks

The door key lock cylinder turns freely
when either the wrong key is used,
or the correct key is not fully inserted.
The free turning door lock feature
prevents the lock from being forced
open. To reset the lock, turn it to the
vertical position with the correct key
fully inserted. Remove the key and
insert it again. If this does not reset
the lock, turn the key halfway around
in the cylinder and repeat the reset
procedure.

Power Door Locks

Press

Q

or

K

on the Remote Keyless

Entry (RKE) transmitter. See

Keyless Entry (RKE) System Operation

Q

:

Press to lock the doors.

K

:

Press to unlock the doors.

The fuel door is also locked or
unlocked using these features.

Delayed Locking

This feature delays the locking of the
doors until five seconds after all doors
are closed.

Delayed locking can only be turned on
when the Unlocked Door Anti-Lockout
feature has been turned off.

When

Q

is pressed on the power door

lock switch while a door or the liftgate
is open, a chime will sound three
times indicating delayed locking is
active.

The doors will lock automatically
five seconds after all doors are closed.
If a door is reopened before that time,
the five-second timer will reset when
all doors are closed again.

Press

Q

on the door lock switch again

or press

Q

on the RKE transmitter to

lock doors immediately.

This feature can also be programmed.
See

Vehicle Personalization

.

«
...
15
16
17
18
19
...
»

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Brand: Kia Pages: 54

Brand: Metra Electronics Pages: 2

Brand: Alpine Pages: 69

Brand: Allen Sports Pages: 2

Wireless Charging Station Universal

Brand: BMW Pages: 160

Brand: Chevrolet Pages: 2

Carpower CAP-20

Brand: Monacor Pages: 2

Tata Indigo Diesel

Brand: TATA Motors Pages: 190

Prime Design HBR-E-FT33B

Brand: Safe Fleet Pages: 12

Brand: Subaru Pages: 16

Brand: FALCON RIDGE Pages: 4

Black Bison Sports Series

Brand: Wald Pages: 7

Brand: Volvo Pages: 286

Brand: Arctic Cat Pages: 101

Brand: Kargo Master Pages: 8

Brand: Prorack Pages: 15

2013 Odyssey Touring

Brand: Honda Pages: 21

Brand: Kia Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands