Cadillac Escalade 2020 Owner'S Manual Download Page 126 | Manualshive

Page: 126 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

126

INSTRUMENTS AND CONTROLS

Traction Control System
(TCS)/StabiliTrak Light

This light comes on briefly when the
engine is started.

If the light does not come on, have
the vehicle serviced by your dealer.
If the system is working normally, the
indicator light turns off.

If the light is on and not flashing, the
TCS and potentially the StabiliTrak/
ESC system have been disabled.
A Driver Information Center (DIC)
message may display. Check the DIC
messages to determine which
feature(s) is no longer functioning and
whether the vehicle requires service.

If the light is on and flashing, the TCS
and/or the StabiliTrak/ESC system is
actively working.

See

Traction Control/Electronic Stability

Engine Coolant
Temperature Warning Light

This light comes on briefly while
starting the vehicle.

If it does not, have the vehicle
serviced by your dealer. If the system
is working normally the indicator light
goes off.

Caution

The engine coolant temperature
warning light indicates that the
vehicle has overheated. Driving with
this light on can damage the engine
and it may not be covered by the
vehicle warranty. See

.

The engine coolant temperature
warning light comes on when the
engine has overheated.

If this happens, pull over and turn off
the engine as soon as possible. See

Engine Overheating

.

Tire Pressure Light

For vehicles with the Tire Pressure
Monitor System (TPMS), this light
comes on briefly when the engine is
started. It provides information about
tire pressures and the TPMS.

When the Light Is On Steady

This indicates that one or more of the
tires are significantly underinflated.

A Driver Information Center (DIC) tire
pressure message may also display.
Stop as soon as possible, and inflate

«
...
124
125
126
127
128
...
»

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Brand: Menabo Pages: 12

Brand: Icom Pages: 20

Brand: Thule Pages: 8

Brand: Cadillac Pages: 20

RUDDER ANGLE INDICATOR

Brand: VDO Pages: 8

Brand: Chevrolet Pages: 372

Brand: Mercedes-Benz Pages: 39

Brand: travall Pages: 2

Brand: Gacell Pages: 12

Brand: AEM Pages: 27

FOLDING TOP 1971

Brand: Fisher Body Pages: 37

Brand: Manik Pages: 2

Brand: Yakima Pages: 28

Brand: Connects2 Pages: 8

Brand: Summit Racing Pages: 11

Brand: Volvo Pages: 18

Powerbuilt 648601

Brand: AllTrade Pages: 3

SportQuest Series

Brand: Perrycraft Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands