Cadillac Escalade 2020 Owner'S Manual Download Page 110 | Manualshive

Page: 110 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

110

INSTRUMENTS AND CONTROLS

The 220V/230V power outlet is on the
rear of the center console.

An indicator light on the outlet turns
on to show it is in use. The light
comes on when the vehicle is started,
equipment requiring less than 150
watts is plugged into the outlet, and
no system fault is detected.

The indicator light does not come on
when the ignition is off or if the
equipment is not fully seated into the
outlet.

If equipment is connected using more
than 150 watts or a system fault is
detected, a protection circuit shuts off
the power supply and the indicator
light turns off. To reset the circuit,
unplug the item and plug it back in or
turn the ignition off and then back to
on. The power restarts when
equipment using 150 watts or less is
plugged into the outlet and a system
fault is not detected.

The power outlet is not designed for
the following, and may not work
properly if they are plugged in:

.

Equipment with high initial peak
wattage, such as
compressor-driven refrigerators
and electric power tools

.

Other equipment requiring an
extremely stable power supply,
such as microcomputer-controlled
electric blankets and touch sensor
lamps

.

Medical equipment

Wireless Charging

The system operates at 145 kHz and
wirelessly charges one Qi compatible
smartphone. The power output of the
system is capable of charging at a rate
up to 1 amp (5W), as requested by the
compatible smartphone.

{

Warning

Wireless charging can affect the
operation of an implanted
pacemaker or other medical devices.
If you have one, it is recommended
to consult with your doctor before
using the wireless charging system.

The vehicle must be on, in ACC/
ACCESSORY, or Retained Accessory
Power (RAP) must be active. The
wireless charging feature may not
correctly indicate charging when the
vehicle is in RAP. See

Accessory Power (RAP)

The operating temperature is

−

20 °C

(

−

4 °F) to 60 °C (140 °F) for the

charging system and 0 °C (32 °F) to
35 °C (95 °F) for the phone.

{

Warning

Remove all objects from the
charging pad before charging your
compatible smartphone. Objects,
such as coins, keys, rings, paper
clips, or cards, between the
smartphone and charging pad will
become very hot. On the rare
occasion that the charging system
does not detect an object, and the
object gets wedged between the
smartphone and charger, remove
the smartphone and allow the

(Continued)

«
...
108
109
110
111
112
...
»

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Brand: Valeo Pages: 17

Brand: Back View Pages: 168

Brand: EAL Pages: 4

Brand: Wagan Pages: 12

21 COVERT Series

Brand: Code 3 Pages: 16

Brand: Phonocar Pages: 2

Brand: FALCON RIDGE Pages: 8

Brand: Scosche Pages: 8

PRIME DESIGN URX-001-E

Brand: Safe Fleet Pages: 8

Brand: ULTIMATE SPEED Pages: 40

Brand: Whispbar Pages: 63

Brand: Classic AutoAir Pages: 44

84 61 0 028 926

Brand: BMW Pages: 13

Brand: Roadtrek Pages: 61

Brand: Mitsubishi Pages: 367

Brand: Aston Martin Pages: 415

Brand: Jaeger Pages: 11

Brand: ATS Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands