CADDX RANGER 7600, Installation Manual

Page: 13 / 38

13
LOCATION 096-097: PROGRAMMING TO REPORT DOWNLOADING COMPLETE
Locations 096-097 contain the communicator codes sent each time a download session has been completed. The
report will come in after a disconnect has been made from a downloading session. Location 096 contains the
standard communicator code, and location 097 contains the extended communicator code. If locations 096-097 are
"0", this report is disabled. When Contact ID is selected, program the extended or the second location with any
number to activate.
LOCATION 098-099: PROGRAMMING FOR AUTOTEST REPORTS
The Ranger 7600 has the ability to send autotest reports at intervals from 1 to 15 days. Locations 098-099 contain
the communicator codes sent for autotest. Location 098 contains the standard communicator code, and location 099
contains the extended code. If locations 098-099 are "0", autotest is disabled. When Contact ID is selected, program
the extended, or second location with any number to activate.
(NOTE: WHEN USING AUTOTEST, LOCATIONS 152-166 MUST BE PROGRAMMED.)
LOCATION 100-101: PROGRAMMING THE 7600 TO REPORT FAIL TO COMMUNICATE
The 7600 has the ability to send a failure to communicate report each time communication is re-established after
a signal has been unable the report. The data that failed to communicate will not be sent but it can be recovered from
the log. The desired Fail to communicate code is programmed in locations 100-101. If both locations are "0", Fail
to Communicate will not be reported. Location 100 contains the standard digit, and location 101 contains the
extended digit. When Contact ID is selected, program the extended, or second location with any number to activate.
LOCATION 102: PROGRAMMING TO REPORT CLOSING
The Ranger 7600 has the ability to report a closing code each time the control is armed. Program the desired
closing-code in Location 102. If this location contains a "0", closing will not be reported. When using a one button
"Quick Arm" code or the Remote Arming input, the man number is 1. When using the Auto Arm feature, the man
number is 9. The closing report will not be initiated until the end of the exit delay. When Contact ID is selected,
program with any number to activate this report..
LOCATION 103: PROGRAMMING TO REPORT OPENINGS
The Ranger 7600 has the ability to report an opening code each time the control is disarmed. Program the desired
opening code in Location 103. If this location contains "0", openings will not be reported. When using the remote
arming input, the man number is 1. When Contact ID is selected, program with any number to activate this report..
LOCATION 104-105: PROGRAMMING THE COMMUNICATOR CODE FOR ZONE 1
Locations 104-105 contains the communicator code to be reported each time zone 1 creates an alarm. Location 104
contains the standard digit, and location 105 contains the extended digit. When using Contact ID format, the number
programmed in location 104 is sent as the Zone ID. On location 105 Refer to Appendix 2. If left unprogrammed, it
will follow the Zone type.
LOCATION 106-107: PROGRAMMING THE COMMUNICATOR CODE FOR ZONE 2
Locations 106-107 contain the communicator code to be reported each time zone 2 creates an alarm. Location 106
contains the standard digit, and location 107 contains the extended digit. When using the Contact ID format, the
number programmed in location 106 is sent as the Zone ID. On location 107 refer to Appendix 2. If left
unprogrammed, it will follow the Zone type.
LOCATION 108-109: PROGRAMMING THE COMMUNICATOR CODE FOR ZONE 3
Locations 108-109 contain the communicator code to be reported each time zone 3 creates an alarm. Location 108
contains the standard digit, and location 109 contains the extended digit. When using the Contact ID format, the
number programmed in location 108 is sent as the Zone ID. On location 109 refer to Appendix 2. If left
unprogrammed, it will follow the Zone type.