CADDX NetworX NX-8 User Manual Download Page 6

6

Ready Light

The 

ready light is “on” when the system is ready to arm and “flashes” if ready to

force arm. The 

ready light is off when the system is not ready to arm because

of a zone(s) being faulted.

Stay Light

The 

stay light is “on” when the all interior (motion detector) zones are

bypassed.

Zone Light

The 

zone lights are “off” when everything is normal. A zone light will be “on” if

the zone has been bypassed. If a 

zone light is “flashing”, that zone is in alarm

or has been faulted. If a 

zone light is “flashing” rapidly, it means that the zone is

in a trouble condition.   Trouble conditions are:

ƒ

 

Tamper

ƒ

 

Hardware

ƒ

 

Low Battery

ƒ

 

Loss of Supervision

(A combination of Alarm/Fault and Tamper/Trouble will produce a rapid
“flashing” light for a short period of time, followed by a slow “flashing” light.)

EMERGENCY ACTIVATION KEYS

NOTES: You must hold these keys for 2 seconds to activate these
functions.   Your system may not be programmed for these activation keys
(see page 1). 
You should press these keys only in an emergency situation that
requires response by emergency personnel.   If your system is programmed for
these functions, the following reports can be sent.

Fire Key – This key can activate the fire alarm when pressed for two seconds. If
your system is connected to a monitoring center, an emergency report could be
sent to that center.

Auxiliary Emergency Key – This key can activate the auxiliary alarm when
pressed for two seconds. If your system is connected to a monitoring center, an
emergency report could be sent to that center.

Police (Panic/Hold-Up) Key - This key can sound a local audible alarm when
pressed for two seconds. If your system is connected to a monitoring center, an
emergency report could be transmitted to that center.  NOTE: Some Panic/Hold-
Up alarms are programmed to be silent at the protected site while reporting an
alarm to the monitoring center. Check with your installing company to determine
how your security system will respond to the Panic/Hold-Up activation.

Summary of Contents for NetworX NX-8



















Reviews: