ELEMENT REPLACEMENT
There will be times when you need to replace your toaster's elements.
This
does not mean your toaster is defective.
With many contributing factors, such
as electrical wiring, amount of usage, power surges, and even normal wear and
tear, elements can fail.
If any of your patented KoverTec elements fail within the first two years after
toaster purchase, Cadco will gladly send the replacement elements to you, free
of charge. By simply following the instructions on this page, you will be toasting
again, easily, and
in less than five minutes!
**UNPLUG TOASTER BEFORE REPLACING ELEMENTS!**
1. Remove Crumb Tray at bottom of toaster.
2. Determine which element(s) are not working. (See diagrams on facing page.)
This step is the most critical to remember;
the end elements have less
wattage than the center elements due to the fact that they only toast one
side of the bread. The elements are clearly marked as center or end elements.
3. Setting the toaster on a cloth, turn toaster up-side down.
4. Unscrew and remove the rubber feet.
5. Unscrew and remove the base plate.
6. Loosen the 2 nuts holding elements in place.
7. Note the position of the
connecting links before
removing the retaining
screws.
8. Lightly bend back the
Element Retaining Strip
and remove the damaged
element by lifting.
9. Replace with a new element
by lowering element in place.
10. Fasten connecting links (nuts)
into place.
12. Slide retaining strip back into place
and tighten nuts.
13. Screw base plate back on.
14. Screw feet back into place.
6
IMPORTANT NOTE: Replacing Cadcos Dualit Toaster Elements
When replacing toaster elements, please note that the
Element Retaining Strip
goes on the
top
of the older mica elements
, but it goes in the
top side notches
of the newer KoverTec Mica elements.
Older
Mica Element
Top side notch
Top of
element
Newer
KoverTec Element
3
TABLE OF CONTENTS
Four-Slot Buffet Toaster (CBF-4M) Instructions ............................................ 3
Four-Slot Standard Toasters (CTS-4 & CTW-4M) Instructions......................... 4
Six-Slot Standard Toasters (CTW-6) Instructions ........................................... 4
Two-Slot Standard Toasters (CTW-2 & CTB-2) Instructions ............................ 4
Two-Slot Bagel Toaster (CBT-2 & CBT-2B) Instructions ................................... 4
Element Replacement (All Models) .................................................................. 6
Tips on Toasting................................................................................................ 8
Cleaning Instructions ...................................................................................... 8
Warranty Information ........................................................................................ 8
A.
Manual timer dials (left one controls left 2 slots; right one controls right 2 slots)
B.
Ejector knobs (each knob lowers or ejects toast from the 2 slots above it)
C.
Pull-out crumb tray
Manual timer
dial
Features dual controls for independent 2-slot operation
INSTRUCTIONS FOR 4-SLOT BUFFET TOASTER
1) Prior to the initial use or after the toaster has not been used for a period of
time (60-90 minutes) it is important to preheat your toaster. This avoids
uneven toasting and will provide a more efficient toasting throughout the
day. To preheat before your buffet line opens, turn BOTH manual timer dials
on. Preheat for at least 1 - 2 minutes.
2) After preheating, lift up the appropriate ejector knob, see
B
above, placing
bread in proper slots. Turn the corresponding timer dial to the desired
darkness setting, see
A
above.
By
turning the timer dial on, your toasting
cycle will begin immediately.
3) The left timer dial should be used when toasting 1 or 2 slices of product in
the left slots. The right timer dial should be used when toasting 1 or 2 slices
of product in the right slots.
4) When the timer reaches zero, a series of light beeps will indicate that the
toasting cycle is complete. You can interrupt the toasting cycle at any time
by lowering the ejector knob for the desired slots. This will also enable you
to check the product for doneness without shutting the toaster off or interrupting
the toasting cycle.
5) To eject the toast, press lightly down on the appropriate ejector knob. The
toast will remain in the slots until you do this (a keep-warm feature appreciated
in the commercial industry.)
C
Ejector knob area label
A
A
B
120 volts / 1750 watts / 14.5 amps / single phase
4-SLOT BUFFET TOASTER - CBF-4M
Up to
Toast
Down to
Serve
Up to
Toast
Down to
Serve
TM
D
ark
-
Med
-
Li
gh
t
Tu
rn
to
To
as
t
0
