background image

*

For further details go to the "Warranty" section of the 

www.cadco-ltd.com 

website

 

5

 

 

-

 

Interventions, alterations or modifications not expressly 
authorized that do not comply with the indications in this 
manual shall invalidate the warranty*. 

-

 

Installation or maintenance that fails to respect the indications 
in this manual may cause damage, injury or fatal accidents. 

-

 

Persons not involved with appliance installation may not pass 
through or occupy the work area during appliance assembly. 

-

 

If the equipment is installed on mobile bases or stacked in 
columns, be sure to use only CADCO components and respect 
the instructions on their packaging. 

-

 

Given its potential danger, the packaging material must be kept 
out of reach of children and animals, and correctly disposed of 
in compliance with local  regulations. 

-

 

The ratings plate provides essential technical information that 
is of utmost importance for any appliance maintenance or 
repairs. Do not remove, damage or modify the plate. 

-

 

Failure to follow these instructions can cause damage and 
injury or death, voids the warranty* and exempts CADCO, Ltd. 
from any liability. 

-

 

The parts protected by the manufacturer or his agent shall not 
be adjusted by the installer. 

 

SAFETY REGULATIONS FOR USE

 

-

 

Following procedures other than those indicated in this guide 
to use and clean the appliances is considered in- appropriate 
and may cause damage, injury or fatal accidents; in addition to 
invalidating the warranty* and relieving Cadco, Ltd. of all 
liability. 

Summary of Contents for BAKERLUX SHOP.Pro XAKPT-08FS-C


































Reviews: