2
2
3. Assembly Instructions
PLEASE NOTE:
Please ensure all protective packaging and plastic are
removed from the appliance before use.
This appliance may only be used with an approved hose and
regulator.
Connect the regulator to a CADAC 3kg, 5kg or 7kg LPG cylinder prior
to use (Fig. 1).
If you wish to use the appliance with a 9kg cylinder, please ensure
that you have purchased the correct hose and regulator suitable for a
9kg cylinder (Fig. 2).
The hose length should be no less than 600 mm and shall not
exceed 1.2 m and replace when the hose is damaged or shows signs
of brittleness or cracks.
Do not twist or pinch the hose. Ensure that it is routed away from
the Stove Body so as to prevent deterioration / damage to the hose
caused by heat.
Ensure that the appliance valves are in the off position by turning the
knobs fully clockwise to the stop.
Open the gas valve on the cylinder and test for any leaks.
Check all gas connections for any signs of gas leaks.
Your appliance is now ready to be used.
Model: 400
Appliance catagories
I
3B/P (30)
Allowable gasses
Butane, Propane or their mixture
Gas pressure
2.8kPa
Ø110 burner jet no.
86
Ø110 burner nominal usuage
Butane - 240g/h per burner
(240g/h x 2 = 480g/h in total)
Ø110 burner gross nominal heat input
3.3kW per burner
(3.3kW x 2 = 6.6kW in total)
Ø75 burner jet no.
72
Ø75 burner nominal usuage
Butane - 168g/h per burner
(168g/h x 2 = 336g/h in total)
Ø75 burner gross nominal heat input
2.3kW per burner
(2.3kW x 2 = 4.6kW in total)
GB
4. Fitting and Changing the Gas Cylinder
• Before connecting the appliance to a gas cylinder, ensure that the rubber seal on the
Regulator is in position and in good condition.
• Carry out this check each time you fit the appliance to a gas cylinder.
• Blow out any dust from the cylinder opening to prevent possible blockage of the jet.
• Ensure that the appliance valves are in the off position by turning the knobs fully clockwise
to their stop.
• Ensure that the gas cylinder is fitted or changed in a well-ventilated location, preferably
outdoors, away from any source of ignition, such as naked flames and away from other
people.
• Make sure that the gas cylinder is kept upright at all times, connect to the cylinder by
screwing on hand tight until fully engaged.
• Ensure that a complete gas seal has been made (check for the smell of gas around the
connection joint). If there is a leak on your appliance (smell of gas), take it outside
immediately into a well-ventilated flame free location where the leak may be detected and
stopped. To check for leaks on your appliance, do it outside using warm soapy water only,
which is applied to the joints and connections of the appliance. A formation of bubbles will
indicate the gas leak. Do not check for leaks with a naked flame.
• If you cannot rectify the gas leak do not use the appliance, contact your local CADAC
stockist for assistance.
• CADAC gas cylinder valves must only be repaired by an authorised CADAC service centre or
dealer.
• When changing a gas cylinder firstly close the appliance control knobs and then the cylinder valve, making sure the flame is
extinguished, unscrew the regulator. Re-fit the regulator to a full cylinder following the same precautions as described above.
Fig. 4
Fig. 5
503-0674 LEV6 (400, 400F) Mighty 4 Stove - User Manual (SA).indd 2
2021/02/23 08:34:24
