background image

4

TABLE OF CONTENTS

CONTENTS

1 - Ratings & Data - Natural Gas & Propane Gas ......................................................... 2
2 - Dimensions ........................................................................................................... 3
3 - Installation Procedure .......................................................................................... 6
4 - Ventilation & Combustion Air ................................................................................ 7
5 - Connecting Supply & Return Piping ....................................................................... 8
6 - Vent Installation ................................................................................................. 14

7 - Vent System Modification

 .................................................................................... 14

8 - Vent Damper Installation & Instructions ............................................................. 15
9 - Connecting Gas Service ....................................................................................... 16
10 - Electrical Section ............................................................................................... 17
11 - Wiring Diagram ................................................................................................. 18
12 - Lighting Instructions ......................................................................................... 20
13 - Normal Sequence of Operation .......................................................................... 21
14 - General Instructions ......................................................................................... 21
15 - Checking Gas Input Rate To Boiler .................................................................... 23

APPENDIX A - CONTROL MODULE 

A.1 Installation Environment Considerations ................................................................

24

A.2 Electrical Connections .........................................................................................

24

A.3 Adjusting Settings ..............................................................................................

24

A.4 Display ..............................................................................................................

24

A.5 Operation ..........................................................................................................25
A.6 Boiler High Limit Temperature Controller ................................................................

27

A.8 Troubleshooting Error Codes ................................................................................

27

A.9 Intermittent Pilot ................................................................................................

30

B.1 Vent Damper Harness -  Molex Plugs .....................................................................

32

B.2 Vent Damper Troubleshooting Guide ......................................................................

33

P/N IM-BWBB-01

[240011111 REV C, 03/31/2017]

Summary of Contents for BWBBAN000045





































Reviews: