Cabletron Systems TRFOT-2 User Manual Download Page 3

 

NOTICE

 

ii

 

FCC NOTICE

 

This device complies with Part 15 of the FCC rules. Operation is subject to the following 
two conditions: (1) this device may not cause harmful interference, and (2) this device 
must accept any interference received, including interference that may cause undesired 
operation.

 

NOTE:

 

 This equipment has been tested and found to comply with the limits for a Class 

A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to 
provide reasonable protection against harmful interference when the equipment is 
operated in a commercial environment. This equipment uses, generates, and can radiate 
radio frequency energy and if not installed in accordance with the operator’s manual, 
may cause harmful interference to radio communications. Operation of this equipment 
in a residential area is likely to cause interference in which case the user will be required 
to correct the interference at his own expense.

 

WARNING:

 

 Changes or modifications made to this device which are not expressly 

approved by the party responsible for compliance could void the user’s authority to 
operate the equipment.

 

DOC NOTICE

 

This digital apparatus does not exceed the Class A limits for radio noise emissions from 
digital apparatus set out in the Radio Interference Regulations of the Canadian 
Department of Communications.

 

CABLETRON SYSTEMS, INC. PROGRAM LICENSE AGREEMENT 

 

IMPORTANT:

Before utilizing this product, carefully read this License Agreement.

This document is an agreement between you, the end user, and Cabletron Systems, Inc. 
(“Cabletron”) that sets forth your rights and obligations with respect to the Cabletron 
software program (the “Program”) contained in this package. The Program may be 
contained in firmware, chips or other media. BY UTILIZING THE ENCLOSED 
PRODUCT, YOU ARE AGREEING TO BECOME BOUND BY THE TERMS OF THIS 
AGREEMENT, WHICH INCLUDES THE LICENSE AND THE LIMITATION OF 
WARRANTY AND DISCLAIMER OF LIABILITY. IF YOU DO NOT AGREE TO THE 
TERMS OF THIS AGREEMENT, PROMPTLY RETURN THE UNUSED PRODUCT TO 
THE PLACE OF PURCHASE FOR A FULL REFUND.

 

CABLETRON SOFTWARE PROGRAM LICENSE

 

1.

LICENSE. 

You have the right to use only the one (1) copy of the Program provided 

in this package subject to the terms and conditions of this License Agreement.

You may not copy, reproduce or transmit any part of the Program except as 
permitted by the Copyright Act of the United States or as authorized in writing by 
Cabletron.

2.

OTHER RESTRICTIONS.

You may not reverse engineer, decompile, or 

disassemble the Program.

3.

APPLICABLE LAW. 

This License Agreement shall be interpreted and governed 

under the laws and in the state and federal courts of New Hampshire. You accept 
the personal jurisdiction and venue of the New Hampshire courts.

Summary of Contents for TRFOT-2



















Reviews: