Cabletron Systems E2210 Installation Manual Download Page 10 | Manualshive

Page: 10 / 43

Cabletron Systems E2210 Installation Manual Download Page 10

INTRODUCTION

Page 1 - 1

CHAPTER 1

INTRODUCTION

The Cabletron Systems

E2200 Series Full-Duplex Ethernet

Network Adapters Installation Guide

is a simple installation and

reference guide for the Cabletron Systems E2200 Series of Full-
Duplex Ethernet network adapters. The E2200 Series network
adapters connect your ISA Bus, or EISA Bus compatible computer
to an Ethernet network utilizing 10BASE-T twisted pair, and
possibly one of; 10BASE-2 Coaxial cable, Fiber Optic, or
10BASE-5 transceiver technologies. You should read through this
manual to gain a full understanding of the capabilities of the
Cabletron Systems E2200 Series Full-Duplex Ethernet adapters.

1.1

USING THIS MANUAL

This manual is structured so that you can follow sequential
chapters as you install and test the Cabletron E2200 series network
adapters. A

Quick Start

procedure is included for experienced

users; a short cut installation procedure for those who are familiar
with networks, PCs, and Ethernet technology.

Chapter 1,

Introduction

, discusses the capabilities of the Cabletron

Systems E2200 Series network adapters. An

FDSE

Technology

Overview

describes the Full-Duplex Switched Ethernet (FDSE)

technology supported by the E2200 series network adapters.

Chapter 2,

Installing the Adapters

, contains instructions for

installing the E2200 series adapters in ISA Bus or EISA Bus
compatible computers.

Chapter 3,

Secondary Media

, provides instructions for connecting

the network adapters to secondary Ethernet media such as Thin-
Net coax, AUI transceiver, or fiber optics.

Appendix A,

Technical Specifications

, provides specifications for

the E2200 Series adapters and the FDSE network technology.

«
...
8
9
10
11
12
...
»

Summary of Contents for E2210












































Reviews:

No comments