Model No. SX-203
R
&
TTE
approved
1. Remove the back of case from the Bell Push unit.
2. There is a 4-position dipswitch marked 1,2,3 & 4. Use an screwdriver to alter the
dipswitch levers to the “On/Off” position, which can be altered to achieve total
sixteen (16) possible digital codes.
3. Select any combination on the Push Button. Press the Push Button, the Door Chime
unit will sound to indicate that new operation code is registerd and memorized, and
it will only work with it.
4. To re-set the operation code, simply remove the batteries from the Door Chime unit
and rest for 30 seconds, it will erase the memory. Re-insert the batteries into the
Door Chime unit, it will give 2-beeps sound to indicate that it is ready for new code
registration. Press the Push Button to confirm the new code is working.
5. Test to ensure correct operation before final installation.
Push Button
Eg.
Type R2 Device - device where the sound output is created by the initial operation of the control and where the period of sound output
continues for designed duration irrespective of condition of the control.
It is located at the back of the chime unit, press the the button to adjust the sound volume up or down. There is total 8 different volume
levels set, 1=mute and 8=max, the door chime will start operating at sound level 6.
Sound Volume Adjustment
A. Push Button unit
Power
Consumption
: 2 x 3 volt Lithium battery (CR2032 - included)
: 7.0mA - ON
0.003mA - OFF
Problem
Chime does not
sound but LED lights
on Push Button
Chime does not
sound plus no lights
on Push Button LED
Chime sounds without
Push Button being
pressed
Possible Causes
1. Units is out of range (max. range 100M)
2. Push Button and Chime units are not on
same digital code
1. Flat Push Button battery
2. Wrong polarity of battery in Push Button
A similar Wire Free Door Chime product is
operating nearby on the same frequency
digital code
Suggest Remedy
1. Operate the Chime unit within the operation range (100M)
2. Re-set the digital code (see Digital Code Set Up)
1. Change the battery
2. Re-insert battery as internal marking in right polarity
Change the digital code (see Digital Code Set Up)
Important:
There are no serviceable parts in the unit, do not attempt to repair it.
Trouble Shooting & User Hints
Specification
B. Door Chime Unit
Power
Consumption
Operating Temperature
Operating Distance
Selectable Tone
Selectable Digital Code
: 2 x 1.5 volt alkaline batteries (“C”, UM2 & R14 - not included)
: 100mA - ON
0.3mA - Stand By
: -10
∞
C to +40
∞
C
: 100 metres (320 feet approx.) in open field
: Total eight (8) tones available
: Total sixteen (16) possible digital codes
1. Do not mount either unit close to fireplace or expose to high temperatures.
2. Do not expose the Door Chime unit to direct sunlight or moisture.
3. Always use alkaline battery. Please dispose of old, defective batteries in an environmentally friendly manner in accordance with the
relevant legislation.
4. Make sure that no naked flame sources, such as lighted candles, sare placed on the unit.
5. The unit should not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the
unit.
6.
CAUTION:
Replace only with the same or equivalent type of battery that is recommended by the manufacturer.
7.
CAUTION:
Danger of explosion if battery is incorrectly installed or replaced.
Important
The unit comes from the factory on a pre-set radio frequency digital code. However, should your door chime activate intermittently for no
reason at all, it is possible that a similar unit is operating nearby on the same frequency digital code. The encoded frequency of the Push
Button (transmitter) can be changed to avoid this problem. The Door Chime unit is equipped with advanced self-learning operation code
ability therefore no setting is needed.
Digital Code Set Up
a) Line-In Recording: Link up the sound source with the chime unit
by the cable provided. Plug one end of the cable into the line-in
jack located at the side of chime unit, plug another end in to the
earphone jack of the sound source. Adjust the sound volume of the
sound source to a suitable level, so that the quality of sound is
good enough to be used as chime sound. Start playing the music
from the sound source and press & hold the “Record” button on
the chime unit for 10 seconds at the same time. During recording,
the Red LED Light at the back of the chime unit will light up, and
turn off after the recording procedure is completed.
b) Using the built-in microphone: Point the microphone to the music
source, press and hold the “Record” button for 10 seconds.
During recording, the Red LED Light at the back of the chime unit
will light up, and turn off after the recording procedure is
completed.
3) Press the “Test” button once to hear the recorded music, if no change
is required, then the doorbell will play this music as your doorbell
melody whenever the bell push is pressed.
Line-In Jack
