background image

7         By Firstech, LLC    

By Firstech, LLC         6

R@w™@r…”…@b•””Ž@f•Žƒ”‰Ž“

Quick Reference

Quick Reference

Q@w™@r…”…@b•””Ž@f•Žƒ”‰Ž“

Button Duration 

AdditionalProgramming Function / Description
Required

0.5 second

no 

Locks doors and / or arms alarm.

3.5 seconds no 

Panic/vehicle locater (flashes vehicle’s parking lights and sounds siren and horn)

0.5 second

no 

Unlocks doors and / or disarms alarm. 

0.5 second

no 

Aux 1. Triggers the auxiliary 1 output (most commonly used for rear defrost or window roll-down)

2.5 seconds no 

Trunk pop. Triggers the trunk release output and opens the vehicle’s trunk.

0.5 second

no 

Aux 2. Triggers the auxiliary 2 output (most commonly used for rear defrost or window roll-down)

2.5 seconds no 

Activates the remote start. Repeat and remote start will shut off

0.5 second

no 

Turns siren on/off (Note: With the siren off, it will still sound in the event the alarm is triggered)

2.5 seconds no 

Option programming menu 1 - Installers Only

0.5 second

no 

Valet mode (see Valet Mode section for details)

2.5 seconds no 

Turns the shock sensor on/off.  (Alarm or alarm / Starter systems only)

Button(s) Duration 

Function

LED

LED  2nd Car Mode Chirp(s)

0.5 second Valet mode (see Valet Mode Section for details)

Amber

Red

Once On / Twice Off

0.5 second Drive lock. Activates ignition controlled door locks.

Amber

Red

Once On / Twice Off

2.5 seconds Option programming menu 2 - Installers Only.

Solid Amber then  Solid Red then Flash Red Once

Flash Amber

0.5 second Activates passive arming (vehicle will arm/lock 

Amber

Red

Once On / Twice Off

30 seconds after the vehicle is disarmed)

2.5 seconds Activates the 2nd Car function. Your remote has the

Solid Amber then  Solid Red then Flash Red Once On / Twice Off

ability to control two systems with the same remote. 

Flash Amber

You must have the same RF Kit in both of your vehicles.

0.5 second Activates timer start mode. Timer start mode has 

Amber

Red

Once On / Twice Off

multiple programmable settings:  duration settings, 
temperature settings and self start settings.

0.5 second Activates the built in Turbo Timer function. 

Amber

Red

Once On / Twice Off

Additional installation is required when using this 

feature on automatic transmission vehicle’s.

2.5 seconds Car Check (updates vehicle status on remote pager) /  Solid Amber then Solid Red then Flash Red Twice

Secure Auxiliary

Flash Amber

Summary of Contents for MA580















Reviews: