PRODUCT INFORMATION
BULLETIN
105 Bonnie Drive
Butler, PA 16002
724-283-4681
724-283-5939 (fax)
www.bwieagle.com
AIR-EAGLE
®
XLT
900 MHz RF Transmitter
MODEL 441-HH-4-VBR
DESCRIPTION
The A
IR
-E
AGLE
XLTTX
I
s a handheld R.F. transmitter capable of
sending up to four unique digital commands to any Air-Eagle XLT
Receiver. This model is equipped with a vibrating feedback that
confirms to the user that the transmitted signal has reached the
receiver. Any number of transmitters and receivers can be combined to
create a long-range radio frequency system that operates hazardous
or hard-to-reach electrical apparatus from safe, convenient locations of
up to 2500 feet away. Seven user-programmable frequencies allow
multiple transmitters and receivers to operate simultaneously in the
same area without interference.
INITIAL OPERATION SET-UP
This transmitter comes ready to operate, with batteries installed, and
factory programmed to Frequency #1. No setup is necessary unless you
wish to change frequency or transmit mode. (See FREQUENCY
PROGRAMMING AND TRANSMITTING MODE SETUP on pages 2).
SPECIFICATIONS
Keypad
Durable Sealed Membrane Keypad
–
Eliminates Dust, Dirt and Moisture
Failures
Enclosure
ABS UL94 HB
Enclosure with
ring is rated IP54
*Not Waterproof
Protective Ring
SEBS (TPE)
Power Requirements
3.0 VDC
Battery Type
(2) 1.5V lithium each, size AAA, to
equal 3.0VDC nominal.
*Note: Current frequency settings are maintained in flash
memory during battery replacement. No reprogramming of
frequency settings is necessary!
Battery Life
(Active Usage)
Up to 3 months
Battery Life
(Sleep Mode)
Up to 6 months
Transmit Frequency
900 MHz Spread Spectrum
RF Output Power
250 mW
Transmit Channels
Seven Independent Network
Frequencies
Transmit Range
Up to 2500 Feet
Note: Max range figures are estimates, based on free-air terrain with limited sources of
interference. Actual range will vary based on transmitting power, orientation of
transmitter and receiver, height of transmitting antenna, height of receiving antenna,
weather conditions, interference sources in the area, and terrain between receiver and
transmitter, including, but not limited to, indoor and outdoor structures such as walls,
metal objects, trees, buildings, hills, and mountains.
Operating Temperature
-40
o
F to +185
o
F
Dimensions
– 4.25” L x 2.68” W x .91” D
(note: belt clip adds .43” to depth)
CONTROLS & INDICATORS
TX LED
Illuminates
RED
when transmitting in standard mode or
GREEN
in repeater mode. When this LED blinks
RED
during or following a transmission, the battery needs to
be replaced.
See Note #1
Note #1
– The low battery notification signals have been improved to
provide more noticeable indications and to safely disable
communications BEFORE a low battery condition can corrupt internal
memory causing device failure. When a low battery is first detected,
the TX LED will blink several times after all buttons are released. If it is
possible to replace the batteries now, please do so. If not, the operator
has approximately 15 more button activations. During this time, when
a button is depressed and held, the TX LED will blink SLOWLY. The
slow blinking will continue several more times after all buttons are
released. Transmissions are still being sent to the receiver during this
time. When a button is depressed and the TX LED is RAPIDLY
blinking, the RF output is disabled and NO signal will reach the
receiver. The batteries MUST NOW BE REPLACED to resume
normal functions.
Pushbuttons 1 thru 4
Transmits individual button RF codes to the
receiver
Vibrate Alert
Vibration confirming that signal has been
transmitted successfully
APPROVALS
United States (FCC)
MCQ-XB900HP
Canada (IC)
1846A-XB900HP
