background image

GasAlertMicroClip
Operator’s Manual

22

Sensor type

H

2

S, CO, O

2

: Single plug-in electrochemical cell

Combustibles: Plug-in catalytic bead

O

2

 measuring principle  

Capillary controlled concentration 

sensor

Alarm conditions

 TWA alarm, STEL alarm, low alarm, high 

alarm, multi-gas alarm, over limit (OL) alarm, low battery alarm, 
confidence beep, automatic shutdown alarm

Audible alarm  

95 dB at 30 cm (1 ft.) (100 dB typical) variable 

pulsed beeper

Visual alarm

 Red light-emitting diodes (LED)

Display

 Alphanumeric liquid crystal display (LCD)

Backlight

 Activates for 5 seconds when the pushbutton is 

pressed and during an alarm condition

Self-test

 Initiated during activation

Calibration

 Automatic zero and automatic span

Oxygen sensor

 Automatic span on activation (enable/disable)

User field options  

Startup message, confidence beep, 

latching alarms, enable/disable safe display mode, oxygen 
measurement, combustible sensor measurement, sensor 
disable, define calibration interval, force calibration, calibration 
lock, force bump, define bump interval, bump due lock, stealth 
mode, language selection, enable/disable automatic oxygen 
calibration, enable/disable auto zero at startup, define alarm 

setpoints, define span concentration values, define STEL 
calculation period, low alarm acknowledge, IntelliFlash, 
confidence beep, and IntelliFlash interval

Battery  Operating Time

XL

XT

Typical Battery 
Life*

18 hours 
Recharges in less 
than 6 hours

10 hours 
Recharges in less 
than 4 hours

Cold Weather 
Battery Life**

After 2 years:
12 hours at -4°F / -
20°C

*Approximately 20% capacity loss is normal wi h lithium 
polymer batteries after 500 charge cycles. Refer to the 
Operator’s Manual for additional information.
**Battery is guaranteed to have 12 hour runtime during 
warranty period under normal operating temperature of -
4°F / -20°C to 122°F/50°C.

Summary of Contents for Micro Clip XL
























Reviews: