BVM GO FLY GOLD Assembly And Operating Manual Download Page 16 | Manualshive

Page: 16 / 23

background image

Ultra Bandit EVO

Assembly & Operation Manual

BVM ® 2019

12

11/12/2019

FUEL SYSTEM

The fuel system is factory installed. Please read the
“Go Fly Fuel System Check” article supplied with your
manual package.

Both Main Tanks and Header tank are shown.

NOTE: We use Safety Wire inside the tanks to secure
fittings and we use Spring Clamps on the outside.

This has been done for you.



Your Bandit will have a factory

installed UAT Mount that also holds
the Pump and ECU.

«
...
14
15
16
17
18
...
»

Summary of Contents for GO FLY GOLD
























Reviews:

No comments

Related manuals for GO FLY GOLD

BLACK FOREST FARM WITH BAKING COTTAGE

Brand: Faller Pages: 12

Brand: Eduard Pages: 7

Little Friendlies Swing & Shake Monkey Rattle

Brand: VTech Baby Pages: 11

Brand: Hyperion Pages: 41

Brand: Eduard Pages: 6

L5198 Bubble Mower

Brand: Fisher-Price Pages: 28

Brand: Faller Pages: 8

Steaman Aerobatic Biplane

Brand: REVELL Pages: 12

Albatross D III

Brand: REVELL Pages: 6

Brand: Faller Pages: 4

COLLECT & BUILD RACECAR RALLY Series

Brand: K'Nex Pages: 20

Brand: Kyosho Pages: 4

35cc EXTRA 300 ARF-QB

Brand: AeroWorks Pages: 80

GAMETIME HOCKEY RINK

Brand: OYO Sports Pages: 60

Brand: Hornby Pages: 2

Brand: Mega Bloks Pages: 32

Computer Cool School Fun2Learn

Brand: Fisher-Price Pages: 23

MARBLE COASTER RUN

Brand: K'Nex Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands